% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/ConcentricTransmon.md (included below). # ConcentricTransmon The PCell declaration for a concentric transmon. **Source:** KQC (KQCircuits). **Category:** qubit. **Module:** `kqcircuits.qubits.concentric_transmon`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of ConcentricTransmon](../../images/components/ConcentricTransmon.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `coupler_1` | 310.099 | -112.867 | 340 | 10 | 6 | coupler port (readout / bus); LOM node `coupler_1` | | `coupler_2` | 165 | 285.788 | 60 | 3 | 32 | coupler port (readout / bus); LOM node `coupler_2` | | `coupler_3` | -285.788 | -165 | 210 | 4.5 | 20 | coupler port (readout / bus); LOM node `coupler_3` | | `drive` | 200 | -346.41 | 300 | 10 | 6 | drive / charge line end; control line (drive) in the LOM | a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `mirror_squid` | `false` | – | Mirror SQUID by its Y axis | | `junction_type` | `"Manhattan"` | – | Junction Type | | `junction_width` | `0.02` | μm | Junction width for code generated element | | `outer_island_width` | `80` | μm | Outer island radial width | | `ground_gap` | `80` | μm | Ground plane padding | | `squid_angle` | `120` | degrees | Angular position of the Josephson Junction/s, where the positive x-axis | | `couplers_r` | `290` | [μm] | Radius of the couplers positioning | | `couplers_a` | `[10, 3, 4.5]` | [μm] | Width of the coupler waveguide's center conductors | | `couplers_b` | `[6, 32, 20]` | [μm] | Width of the coupler waveguide's gaps | | `couplers_angle` | `[340, 60, 210]` | [degrees] | Positioning angles of the couplers, where 0deg corresponds to positive x-axis | | `couplers_width` | `[10, 20, 30]` | [μm] | Radial widths of the arc couplers | | `couplers_arc_amplitude` | `[35, 45, 15]` | [degrees] | Couplers angular extension | | `drive_angle` | `300` | degrees | Angle of the drive port, where 0deg corresponds to positive x-axis | | `loop_area` | `100` | μm^2 | Loop area | | `fluxline_type` | `"Fluxline Standard"` | – | Fluxline Type | | `r_inner` | `120` | μm | Internal island radius | | `r_outer` | `250` | μm | External island radius, measured at the outer edge | | `drive_distance` | `400` | µm | Distance of the driveline, measured from qubit centre | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X_1` | C | island1 – gnd | estimate=122, unit=fF, estimate_source=analytic: ring outer edge as half CPW, estimate_kind=analytic, uncertainty=±25% | | `C_X_12` | C | island1 – island2 | estimate=91, unit=fF, estimate_source=rough: disk–ring facing edges as coplanar strips along the mean circumference, estimate_kind=rough, uncertainty=±50% | | `C_X_2` | C | island2 – gnd | estimate=19, unit=fF, estimate_source=rough: disk to ground screened by the ring, estimate_kind=rough, uncertainty=±50% | | `J_X` | SQUID | island1 – island2 | Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 | | `Cg_X_coupler_1` | C | island1 – coupler_1 | estimate=12, unit=fF, estimate_source=rough: arc 177 µm facing the island across 35 µm (CPS), estimate_kind=rough, uncertainty=±50% | | `Cc_X_coupler_1` | C | coupler_1 – gnd | estimate=13, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% | | `Cg_X_coupler_2` | C | island1 – coupler_2 | estimate=19, unit=fF, estimate_source=rough: arc 228 µm facing the island across 30 µm (CPS), estimate_kind=rough, uncertainty=±50% | | `Cc_X_coupler_2` | C | coupler_2 – gnd | estimate=15, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% | | `Cg_X_coupler_3` | C | island1 – coupler_3 | estimate=7, unit=fF, estimate_source=rough: arc 76 µm facing the island across 25 µm (CPS), estimate_kind=rough, uncertainty=±50% | | `Cc_X_coupler_3` | C | coupler_3 – gnd | estimate=7.2, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% | Nodes: `island1`, `island2`, `coupler_1`, `coupler_2`, `coupler_3`. ## Simulation export notes - C10: route gap strip misses the cell's etch by < 1 nm at an angled / off-grid port (fab build) (status: fixed; fix in route/waveguide.py (joined_nodes, misses_etch); layouts/chips/design_chip.py (DesignChip._join_ends); assembly/plan.py (RoutePlan.joins)) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "ConcentricTransmon", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.coupler_1") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components ConcentricTransmon` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.