% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/CpweFingerCapacitor.md (included below). # CpweFingerCapacitor Interdigital capacitor interrupting the centre line (legacy ``cpwe.finger_cap``); ports ``a`` (−x), ``b``. **Source:** Quantcore. **Category:** capacitor. **Module:** `quantcore_circuits.layouts.others.cpwe`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of CpweFingerCapacitor](../../images/components/CpweFingerCapacitor.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `a` | 0 | 0 | 180 | 10 | 6 | CPW end; LOM node `a` | | `b` | 52 | 0 | 0 | 10 | 6 | CPW end; LOM node `b` | a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `finger_gap` | `2` | μm | Finger separation (legacy f_sep) | | `finger_length` | `50` | μm | Finger length (legacy f_length) | | `fingers` | `4` | – | Number of fingers (legacy f_n) | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | a – b | estimate=6.99, unit=fF, estimate_source=analytic: 4 fingers 1 µm / 2 µm, overlap 48 µm (Igreja & Dias 2004) + tips, estimate_kind=analytic, uncertainty=±25% | | `C_X_a` | C | a – gnd | estimate=3.8, unit=fF, estimate_source=rough: half the capacitor section as CPW, estimate_kind=rough, uncertainty=±50% | | `C_X_b` | C | b – gnd | estimate=3.8, unit=fF, estimate_source=rough: half the capacitor section as CPW, estimate_kind=rough, uncertainty=±50% | Nodes: `a`, `b`. ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "CpweFingerCapacitor", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components CpweFingerCapacitor` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok.