% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/Flipmon.md (included below). # Flipmon Circular flip-chip transmon (QPDK ``flipmon_with_bbox``), optionally with its plate readout coupler. **Source:** Quantcore. **Category:** qubit. **Module:** `quantcore_circuits.layouts.qubits.qpdk_cells`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of Flipmon](../../images/components/Flipmon.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `coupler` | 170 | 0 | 0 | 10 | 6 | coupler port (readout / bus); LOM node `cplr` | | `squid_a` | 60 | 0 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island2` | | `squid_b` | 80 | 0 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island1` | Pins with direction `none`: `squid_a`, `squid_b`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). **Notes from the catalog:** QPDK flipmon_with_bbox (MIT). Face 2b1 (top-chip disc, its etch, the bump) is on KQC face-2b1 layers, which the PDK maps to 800/0+ (flip-chip). Port 'coupler' is on the M1 etch edge, 13 µm beyond QPDK's plate port o1 at defaults. ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `mirror_squid` | `false` | – | Mirror SQUID by its Y axis | | `junction_type` | `"Manhattan"` | – | Junction Type | | `junction_width` | `0.02` | μm | Junction width for code generated element | | `inner_circle_radius` | `60` | μm | Inner disc radius (M1) | | `outer_ring_radius` | `110` | μm | Outer ring centre radius (M1) | | `outer_ring_width` | `60` | μm | Outer ring width (M1) | | `top_circle_radius` | `110` | μm | Top disc radius (M2, face 1) | | `m1_etch_extension_gap` | `30` | μm | M1 etch radius beyond the ring | | `m2_etch_extension_gap` | `40` | μm | M2 etch radius beyond the top disc | | `junction_position_rotation` | `0` | ° | Junction angle around the centre | | `junction_params` | `"{}"` | – | Junction cell parameters (JSON dict) | | `with_coupler` | `true` | – | Draw the plate readout coupler and its port | | `coupler_width` | `10` | μm | Coupler plate radial width | | `coupler_length` | `58` | μm | Coupler plate length (tangential) | | `coupler_offset` | `10` | μm | Coupler plate centre beyond the ring's outer edge | | `coupler_etch_margin` | `2` | μm | Etch margin around the plate | | `loop_area` | `100` | μm^2 | Loop area | | `fluxline_type` | `"Fluxline Standard"` | – | Fluxline Type | | `bump_diameter` | `15` | μm | Indium bump diameter | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X_1` | C | island1 – gnd | estimate=83.3, unit=fF, estimate_source=analytic: ring 80–140 µm, outer edge as half CPW (30 µm gap), estimate_kind=analytic, uncertainty=±25% | | `C_X_12` | C | island1 – island2 | estimate=46, unit=fF, estimate_source=rough: disc–ring facing edges as coplanar strips along the mean circumference, estimate_kind=rough, uncertainty=±50% | | `C_X_2` | C | island2 – gnd | estimate=5.1, unit=fF, estimate_source=rough: M1 disc to ground screened by the ring, estimate_kind=rough, uncertainty=±50% | | `C_X_12_flip` | C | island1 – island2 | estimate=20, unit=fF, estimate_source=rough: M2 disc r 110 over the M1 ring: parallel plate, 17907 µm² across an assumed 8 µm vacuum gap, estimate_kind=rough, uncertainty=±50% | | `C_X_2_top` | C | island2 – gnd | estimate=71, unit=fF, estimate_source=rough: M2 disc r 110 in its 40 µm top-face gap (single-face formula), estimate_kind=rough, uncertainty=±50% | | `J_X` | SQUID | island1 – island2 | Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 | | `Cg_X_cplr` | C | island1 – cplr | estimate=6.43, unit=fF, estimate_source=analytic: plate 58×10 µm facing the ring across 5 µm (CPS), estimate_kind=analytic, uncertainty=±25% | | `Cc_X_cplr` | C | cplr – gnd | estimate=7.4, unit=fF, estimate_source=rough: plate in the M1 etch + its lead, estimate_kind=rough, uncertainty=±50% | Nodes: `island1`, `island2`, `cplr`. - X: M2 top disc (face 2b1) counted in island2 across an assumed 8 µm flip-chip gap (rough; PDK v2 does not fabricate face 2b1); coupler ↔ disc C neglected (screened by the ring) ## Simulation export notes - C1: Sim junction pads overlap / end on a curved island in a narrow gap (status: fixed; fix in layouts/junctions/sim_gap.py; layouts/qubits/qpdk_cells.py; layouts/qubits/sqdmetal_cells.py) - C2: indium bump in a one-face simulation is a PEC pillar to the top of the box (status: fixed; fix in sim_tools/builder.py) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "Flipmon", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.coupler") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components Flipmon` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).