% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/Gatemon.md (included below). # Gatemon Carbon-nanotube gatemon island in an etched pocket with a gate feed (QPDK ``gatemon``), M1 only. **Source:** Quantcore. **Category:** qubit. **Module:** `quantcore_circuits.layouts.qubits.qpdk_cells`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of Gatemon](../../images/components/Gatemon.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `gate` | 60 | -246 | 270 | 10 | 6 | gate line end; LOM node `gate` | | `readout` | 0 | 75 | 90 | 150 | 40 | readout coupling; LOM node `island` | | `squid_a` | -40 | -75 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island` | | `squid_b` | -40 | -196 | none | 10 | 6 | junction pins (the LOM's L_J); grounded in the LOM | Pins with direction `none`: `squid_a`, `squid_b`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). **Notes from the catalog:** QPDK gatemon (MIT): M1 plus the CNT contacts, nanotube, hBN, Al patches and top gate on the proposed layers 600-604/0 (qpdk_cells.GATEMON_LAYERS; no fab numbers yet, draw_process_layers=False for M1 only). Port 'readout' is the island edge (a = island width, b = pocket_gap_top), not a CPW end: snap it to GatemonCoupler.qubit. ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `island_size` | `[150, 150]` | [μm, μm] | Island (width, height) | | `pocket_gap` | `60` | μm | Island to pocket side walls | | `pocket_gap_top` | `40` | μm | Island to the readout side of the pocket | | `electrode_size` | `[60, 60]` | [μm, μm] | Nb/Au landing pad (width, height) | | `electrode_spacing` | `100` | μm | Gap between the landing pads | | `lead_width` | `2` | μm | Contact stem width | | `junction_length` | `1` | μm | Gap between the contact tips | | `junction_width` | `0.002` | μm | Nanotube placement width | | `junction_offset` | `20` | μm | Stems to weak link (x) | | `hbn_size` | `[80, 80]` | [μm, μm] | hBN footprint (width, height) | | `size_patch` | `[60, 50]` | [μm, μm] | Al reconnection patch (width, height) | | `gate_tip_width` | `16` | μm | Top-gate tip width | | `gate_tip_gap` | `5` | μm | hBN to M1 gate landing clearance | | `gate_length` | `50` | μm | M1 gate CPW beyond the pocket | | `nanotube_contact_overlap` | `0.5` | μm | Tube overlap onto each contact | | `electrode_offset` | `-40` | μm | Contact stems x relative to the island | | `gate_offset` | `100` | μm | Stems to the M1 gate feed (x) | | `draw_process_layers` | `true` | – | Draw contacts, nanotube, hBN, patches and top gate (proposed fab 600–604/0) | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | island – gnd | estimate=51.1, unit=fF, estimate_source=analytic: 150×150 µm island in its pocket (60 µm sides, 40 µm readout side), estimate_kind=analytic, uncertainty=±25% | | `J_X` | JJ | island – gnd | Lj_nH=–, Cj_fF=0 | | `Cgate_X` | C | island – gate | estimate=0.2, unit=fF, estimate_source=rough: M1 gate tip beside the junction, below the island (rough, ±100 %), estimate_kind=rough, uncertainty=±50% | | `C_X_gate` | C | gate – gnd | estimate=16, unit=fF, estimate_source=rough: gate feed CPW, estimate_kind=rough, uncertainty=±50% | Nodes: `island`, `gate`. - X: no junction.Lj_nH in the design; the qubit mode needs one to simulate - X: the CNT junction is not drawn; modelled as a JJ with the design's junction values ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "Gatemon", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.gate") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components Gatemon` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).