% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/GatemonCoupler.md (included below). # GatemonCoupler Straight CPW ``o1`` → ``o2`` with a capacitive island reference port ``qubit`` (QPDK ``gatemon_coupler``). **Source:** Quantcore. **Category:** coupler. **Module:** `quantcore_circuits.layouts.others.qpdk_cells`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of GatemonCoupler](../../images/components/GatemonCoupler.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `o1` | 0 | 0 | 180 | 10 | 6 | LOM node `line` | | `o2` | 600 | 0 | 0 | 10 | 6 | LOM node `line` | | `qubit` | 200 | -45 | 270 | 150 | 40 | LOM node `qubit` | a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). **Notes from the catalog:** QPDK gatemon_coupler (MIT). Port 'qubit' is a capacitive reference plane (a = island_width, b = pocket_gap_top), not a CPW end: snap a Gatemon 'readout' to it. ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `length` | `600` | μm | Line length | | `coupling_position` | `200` | μm | Island centre measured from o1 | | `island_width` | `150` | μm | Island width (reference plane) | | `pocket_gap_top` | `40` | μm | Island edge to conductor edge | | `coupling_capacitance` | `5.4` | fF | Nominal line-island capacitance (LOM) | | `qubit_side` | `"bottom"` | – | Island side of the line | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `Cg_X` | C | line – qubit | estimate=5.4, unit=fF, estimate_source=rough: QPDK nominal coupling_capacitance (cell parameter), estimate_kind=rough, uncertainty=±50% | | line | node | length (µm) | a (µm) | b (µm) | ends | |---|---|---|---|---|---| | `X` | `line` | 600 | 10 | 6 | short / short | Nodes: `line`, `qubit`. ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "GatemonCoupler", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.o1") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components GatemonCoupler` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok.