% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/LumpedJpa.md (included below). # LumpedJpa Lumped JPA: a trilayer junction or SQUID to ground, shunted by an interdigital capacitor (twpa-sim ``jpa`` / **Source:** Quantcore. **Category:** resonator. **Module:** `quantcore_circuits.layouts.others.amplifiers`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of LumpedJpa](../../images/components/LumpedJpa.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `signal` | 0 | 0 | 180 | 10 | 6 | signal line end; LOM node `island` | | `squid_a` | 390 | 0 | none | 10 | 6 | junction pins (the LOM's L_J) | | `squid_b` | 406 | 0 | none | 10 | 6 | junction pins (the LOM's L_J) | Pins with direction `none`: `squid_a`, `squid_b`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `coupling` | `"capacitive"` | – | Coupling to the signal line | | `junction_type` | `"Quantcore Junction"` | – | Junction (trilayer cell) | | `junction_params` | `"{}"` | – | Trilayer junction cell parameters (JSON dict) | | `lead_length` | `50` | μm | CPW lead from the port to the pocket | | `spine_width` | `20` | μm | Island spine width | | `shunt_fingers` | `20` | – | Island fingers per side | | `finger_length` | `100` | μm | Finger length | | `finger_width` | `4` | μm | Finger width | | `finger_gap` | `4` | μm | Gap between fingers (and all island clearances) | | `junction_gap` | `16` | μm | Junction gap (window height) | | `tap_width` | `4` | μm | Inductive coupling strip width | | `tap_pad` | `[20, 24]` | – | Inductive coupling tap pad (length along x, width), µm | | `flux_length` | `200` | μm | Flux line length (port to short) | | `flux_gap` | `2` | μm | Ground strip between the pocket and the flux line gap | | `flux_line` | `false` | – | Draw a shorted flux / pump line past the junction (capacitive) | | `flux_offset` | `20` | μm | Flux short beyond the junction axis | | `flux_phi0` | `0.0` | Φ0 | Static flux bias of a SQUID (LOM) | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | island – gnd | estimate=392, unit=fF, estimate_source=analytic: 2 × IDC (41 fingers 4/4 µm, overlap 96 µm, Igreja–Dias) + spine ends, estimate_kind=analytic, uncertainty=±25% | | `J_X` | JJ | island – gnd | Lj_nH=6.734, Cj_fF=15 | Nodes: `island`. - X: lumped JPA, C_shunt ≈ 392 fF (analytic IDC) ## Simulation export notes - C4: galvanic lead port shorted to ground / leaving the box (status: fixed; fix in sim_tools/builder.py (lead_open_ends, galvanic_routes, build_simulation)) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "LumpedJpa", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.signal") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components LumpedJpa` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).