% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/PadCoupler.md (included below). # PadCoupler Series gap capacitor of two facing pads (legacy ``Coupler``); ports ``left`` / ``right``. **Source:** Quantcore. **Category:** coupler. **Module:** `quantcore_circuits.layouts.others.couplers`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of PadCoupler](../../images/components/PadCoupler.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `left` | -35 | 0 | 180 | 10 | 6 | pad coupling port; LOM node `left` | | `right` | 35 | 0 | 0 | 10 | 6 | pad coupling port; LOM node `right` | a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `pad_thickness` | `20` | μm | Pad thickness (along the axis) | | `pad_height` | `30` | μm | Pad height | | `gap` | `10` | μm | Gap between the pads (junction gap) | | `lead_length` | `10` | μm | Lead length outside each pad | | `junction_type` | `"No Squid"` | – | No junction on a coupler | | `junction_params` | `"{}"` | – | Unused on a coupler | | `pocket_margin` | `20` | μm | Pocket beyond the pads in y (0 = no pocket, legacy) | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | left – right | estimate=1.68, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | | `C_X_left` | C | left – gnd | estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | | `C_X_right` | C | right – gnd | estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | Nodes: `left`, `right`. ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "PadCoupler", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.left") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components PadCoupler` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok.