% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/QuantcoreSquid.md (included below). # QuantcoreSquid The Quantcore PDK SQUID (``junction_type: "Quantcore Squid"``): a symmetric TrilayerSquid whose **whole SQUID** **Source:** Quantcore. **Category:** junction. **Module:** `quantcore_circuits.layouts.junctions.trilayer`. :::{note} Canonical cell of an alias group. Aliases: [`TrilayerSquid`](TrilayerSquid.md). ::: See also the [catalog](../CATALOG.md). ## Pins ![Pins of QuantcoreSquid](../../images/components/QuantcoreSquid.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `common` | 0 | 20 | none | 10 | 6 | junction lead (the LOM's L_J branch); LOM node `j` | Pins with direction `none`: `common`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `junction_type` | `"Quantcore Squid"` | – | Junction Type | | `junction_width` | `0.02` | μm | Junction width for code generated element | | `finger_width` | `0.25` | μm | Straight finger width (junction size) | | `second_finger_width` | `0.6` | μm | Bent finger width (0 = same as straight) | | `window_width` | `32.0` | μm | Exposure window width | | `straight_finger_length` | `3.2` | μm | Straight finger length | | `straight_finger_y` | `-3.6` | μm | Straight finger offset (legacy y) | | `bent_finger_length` | `3.0` | μm | Bent finger length | | `bent_finger_y` | `-2.5` | μm | Bent finger offset (legacy y) | | `bent_pad_width` | `1.0` | μm | Bent finger lead width | | `hsq_width` | `0.2` | μm | HSQ box width | | `junction_spacing` | `8.0` | μm | Distance of each junction from the axis | | `lead_length` | `10.0` | μm | Lead (pad) length of the straight fingers | | `loop_area` | `100` | μm^2 | Loop area | | `window_height` | `20.0` | μm | Exposure window height (= qubit gap it spans) | | `bent_shift` | `0.5` | μm | Bent finger cell shift in y | | `with_hsq` | `true` | – | Draw HSQ sidewall boxes | | `hsq_extra` | `0.2` | μm | HSQ box extra length | | `spacer_gradient` | `true` | – | Spacer gradient: 51–53/0 dose levels inside the 50/0 spacer (width / 3 strips; rings for windows) | | `lj_nH` | `0.0` | nH | Size by the PDK junction rule for this L_J (SQUID: parallel total; 0 = use the finger widths) | | `clearer` | `true` | – | Draw the CLEARER metal box under the windows (base_metal_addition) | | `clearer_inset` | `1.0` | μm | CLEARER inset from the window sides | | `hsq_overlap` | `0.03` | μm | HSQ overlap onto the finger | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `J_X` | SQUID | j – gnd | Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 | Nodes: `j`. ## Simulation export notes - C3: junction sub-cell simulated on its own (status: fixed; fix in sim_tools/builder.py (is_junction_cell, _is_qubit, build_simulation); sim_tools/subset.py (has_junction)) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "QuantcoreSquid", at=(3750, 3750), a=10) # parameters: see the table above # no directed pin: place it with at= / rot=, or snap it with snap= / to= ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components QuantcoreSquid` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect n/a (no directed port), build ok. ports without direction: common (ghost draws boxes).