% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/SuperInductor.md (included below). # SuperInductor The PCell declaration for a Manhattan style single junction. **Source:** KQC (KQCircuits). **Category:** junction. **Module:** `kqcircuits.junctions.super_inductor`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of SuperInductor](../../images/components/SuperInductor.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `common` | 0 | 22 | none | 10 | 6 | junction lead (the LOM's L_J branch); LOM node `j` | Pins with direction `none`: `common`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `junction_type` | `"Super Inductor"` | – | Junction Type | | `junction_width` | `0.02` | μm | Junction width for code generated element | | `junction_length` | `2` | μm | Junction length | | `wire_width` | `0.02` | μm | Wire width | | `phase_slip_junction_length` | `0.5` | μm | Phase slip junction length | | `squid_area_width` | `2` | μm | Width of Squids Area. | | `squid_area_height` | `5` | μm | Height of Squids Area. | | `squid_count` | `8` | – | Number of Squids in the Super Inductor. | | `squid_wire_length` | `0.25` | μm | Length of the wire between SQUIDs. | | `squid_x_connector_offset` | `0.5` | μm | Length of the horizontal connector between the corner of the junction to the wire of the squid. | | `inductor_padding` | `1` | μm | Vertical margin from bends to limit of the circuit | | `taper_horizontal_displacement` | `1` | μm | Horizontal displacement of the taper from the junction. | | `taper_horizontal_displacement_step` | `0.25` | μm | Horizontal displacement step of the taper from the junction. | | `bend_width_multiplier` | `1.5` | – | Relative width of bend according to junction_width | | `shadow_width` | `0.125` | μm | Width of the shadow layer. | | `include_base_metal_gap` | `true` | – | Include base metal gap layer. | | `finger_overlap` | `1.0` | μm | Length of fingers inside the pads. | | `inductor_height` | `22.0` | μm | Height of the junction element. | | `inductor_width` | `22.0` | μm | Width of the junction element. | | `shadow_min_height` | `0.04` | μm | Minimum height of the shadow layer. | | `include_base_metal_addition` | `true` | – | Include base metal addition layer. | | `shadow_margin` | `0.5` | μm | Shadow layer margin near the the pads. | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `J_X` | JJ | j – gnd | Lj_nH=–, Cj_fF=0 | Nodes: `j`. ## Simulation export notes - C3: junction sub-cell simulated on its own (status: fixed; fix in sim_tools/builder.py (is_junction_cell, _is_qubit, build_simulation); sim_tools/subset.py (has_junction)) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "SuperInductor", at=(3750, 3750), a=10) # parameters: see the table above # no directed pin: place it with at= / rot=, or snap it with snap= / to= ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components SuperInductor` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.