% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/TransmonTaperedInsets.md (included below). # TransmonTaperedInsets Floating tapered-pad transmon in a filleted pocket (SQDMetal ``TransmonTaperedInsets``). **Source:** Quantcore. **Category:** qubit. **Module:** `quantcore_circuits.layouts.qubits.sqdmetal_cells`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of TransmonTaperedInsets](../../images/components/TransmonTaperedInsets.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `bottom_left_pin` | -550 | -75 | 90 | 10 | 6 | LOM node `island2` | | `bottom_pocket_pin` | 0 | -400 | 180 | 10 | 6 | grounded in the LOM | | `bottom_right_pin` | 550 | -75 | 90 | 10 | 6 | LOM node `island2` | | `squid_a` | 0 | 18 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island1` | | `squid_b` | 0 | -18 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island2` | | `top_left_pin` | -550 | 135 | 0 | 10 | 6 | LOM node `island1` | | `top_pocket_pin` | 0 | 400 | 0 | 10 | 6 | grounded in the LOM | | `top_right_pin` | 550 | 135 | 0 | 10 | 6 | LOM node `island1` | Pins with direction `none`: `squid_a`, `squid_b`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). **Notes from the catalog:** SQDMetal TransmonTaperedInsets (Apache-2.0). The corner and pocket pins keep SQDMetal's normals (top_*_pin +x, bottom_*_pin +y, top_pocket_pin +x, bottom_pocket_pin -x): placement marks in or at the pocket, not CPW ends. Connection-pad ports are CPW ends. ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `mirror_squid` | `false` | – | Mirror SQUID by its Y axis | | `junction_type` | `"Manhattan"` | – | Junction Type | | `junction_width` | `0.02` | μm | Junction width for code generated element | | `inductor_width` | `20` | μm | Junction line width | | `inductor_height` | `36` | μm | Junction line length | | `junction_pin_inset` | `0` | μm | Junction pins inset from the pad edge | | `pad_gap` | `100` | μm | Gap between the pads | | `pad_width` | `800` | μm | Pad width (x, without the round ends) | | `pad_height` | `110` | μm | Pad height (y) | | `pocket_width` | `1000` | μm | Pocket width | | `taper_width_top` | `40` | μm | Taper width at the junction | | `taper_width_base` | `200` | μm | Taper width at the pad | | `taper_height` | `40` | μm | Taper height (0 = no taper) | | `taper_fillet_radius` | `3` | μm | Taper corner radius | | `junction_position` | `"center"` | – | Junction position (SQDMetal junction_centered True / False / 'left') | | `junction_x_offset` | `0` | μm | Junction offset from the pad end (right / left) | | `inset_width` | `0` | μm | Inset width (0 = none) | | `inset_fillet_radius` | `10` | μm | Inset corner radius | | `fillet_radius` | `50` | μm | Pad fillet radius | | `fillet_radius_gap` | `50` | μm | Pocket corner radius | | `coupled_pad_height` | `0` | μm | Coupler teeth height (0 = none) | | `coupled_pad_width` | `0` | μm | Coupler teeth width | | `coupled_pad_gap` | `0` | μm | Gap between the coupler teeth | | `connection_pads` | `"{}"` | – | Connection pads (JSON {name: {options}}) | | `junction_params` | `"{}"` | – | Junction cell parameters (JSON dict) | | `loop_area` | `100` | μm^2 | Loop area | | `fluxline_type` | `"Fluxline Standard"` | – | Fluxline Type | | `chrgln_pin_x_offset` | `30` | μm | Corner pins: offset along y from the pad centre line | | `chrgln_pin_y_offset` | `50` | μm | Corner pins: offset along x from the pocket edge | | `pocket_height` | `800` | μm | Pocket height | | `pocket_lower_tighten` | `120` | μm | Pocket shortened from below by | | `inset_depth` | `100` | μm | Inset depth | | `fillet_resolution` | `16` | – | Fillet points per quarter circle | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X_1` | C | island1 – gnd | estimate=92.7, unit=fF, estimate_source=analytic: 910×110 µm pads across 100 µm in a 1000×800 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | | `C_X_2` | C | island2 – gnd | estimate=106, unit=fF, estimate_source=analytic: 910×110 µm pads across 100 µm in a 1000×800 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | | `C_X_12` | C | island1 – island2 | estimate=44.4, unit=fF, estimate_source=analytic: 910×110 µm pads across 100 µm in a 1000×800 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% | | `J_X` | SQUID | island1 – island2 | Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 | Nodes: `island1`, `island2`. ## Simulation export notes - C1: Sim junction pads overlap / end on a curved island in a narrow gap (status: fixed; fix in layouts/junctions/sim_gap.py; layouts/qubits/qpdk_cells.py; layouts/qubits/sqdmetal_cells.py) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "TransmonTaperedInsets", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.bottom_left_pin") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components TransmonTaperedInsets` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route. GUI status (`kplugin/COMPONENTS_STATUS.md`): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).