% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/metal_CapNInterdigitalTee.md (included below). # metal:CapNInterdigitalTee Generates a three pin (+) structure comprised of a primary two pin CPW **Source:** Metal (Qiskit Metal). **Category:** coupler. **Module:** `qiskit_metal.qlibrary.couplers.cap_n_interdigital_tee`. See also the [catalog](../CATALOG.md). ## Pins ![Pins of metal:CapNInterdigitalTee](../../images/components/metal_CapNInterdigitalTee.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `prime_end` | 50 | 0 | 0 | 10 | 6 | LOM node `prime` | | `prime_start` | -50 | 0 | 180 | 10 | 6 | LOM node `prime` | | `second_end` | 0 | -146 | 270 | 10 | 6 | LOM node `second` | a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `junction_type` | `"Metal"` | – | Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line | | `junction_params` | `"{}"` | – | Trilayer junction cell parameters (JSON dict, e.g. lj_nH) | | `metal_class` | `"CapNInterdigitalTee"` | – | Quantum Metal component | | `options` | `"{}"` | – | Metal options as JSON (bare numbers on length options are µm) | | `open_pins` | `""` | – | Pins left open (comma-separated): keep Metal's etch beyond them, as drawn with no route attached | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | prime – second | estimate=5.26, unit=fF, estimate_source=analytic: IDC, estimate_kind=analytic, uncertainty=±25% | | `C_X_second` | C | second – gnd | estimate=7.4, unit=fF, estimate_source=rough: second-line stub to ground, estimate_kind=rough, uncertainty=±50% | Nodes: `prime`, `second`. ## Simulation export notes - C10: route gap strip misses the cell's etch by < 1 nm at an angled / off-grid port (fab build) (status: fixed; fix in route/waveguide.py (joined_nodes, misses_etch); layouts/chips/design_chip.py (DesignChip._join_ends); assembly/plan.py (RoutePlan.joins)) ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "metal:CapNInterdigitalTee", at=(3750, 3750), a=10) # parameters: see the table above d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to d.route("L1", "PAD.a", "U1.prime_end") # a CPW from the pad to the pin ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components metal:CapNInterdigitalTee` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.