% generated by scripts/make_component_docs.py -- do not edit. Put hand-written notes in docs/components/notes/metal_TransmonStar.md (included below). # metal:TransmonStar The base `TransmonStar` class. **Source:** Metal (Qiskit Metal). **Category:** qubit. **Module:** `qiskit_metal.qlibrary.qubits.transmon_star`. :::{note} Alias of [`metal:TransmonCross`](metal_TransmonCross.md): the same circuit, drawn differently. num_points 4, arm_length / arm_width / arm_gap → cross_length / cross_width / cross_gap, junction_arm_index 3 (XOR 0); claws: arm_index instead of connector_location ::: See also the [catalog](../CATALOG.md). ## Pins ![Pins of metal:TransmonStar](../../images/components/metal_TransmonStar.png) Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm. | pin | x (µm) | y (µm) | direction (°) | a (µm) | b (µm) | purpose | |---|---|---|---|---|---|---| | `squid_a` | 150 | 0 | none | 10 | 6 | junction pins (the LOM's L_J); LOM node `island` | | `squid_b` | 170 | 0 | none | 10 | 6 | junction pins (the LOM's L_J); grounded in the LOM | Pins with direction `none`: `squid_a`, `squid_b`. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to. a, b: CPW centre width and gap where the pin declares them (`–` = not declared). Position and direction are in the cell's own frame (`at=(0, 0)`, `rot=0`). ## Parameters | name | default | unit | description | |---|---|---|---| | `a` | `10` | μm | Width of center conductor | | `b` | `6` | μm | Width of gap | | `r` | `100` | μm | Turn radius | | `junction_type` | `"Metal"` | – | Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line | | `junction_params` | `"{}"` | – | Trilayer junction cell parameters (JSON dict, e.g. lj_nH) | | `metal_class` | `"TransmonStar"` | – | Quantum Metal component | | `options` | `"{}"` | – | Metal options as JSON (bare numbers on length options are µm) | | `open_pins` | `""` | – | Pins left open (comma-separated): keep Metal's etch beyond them, as drawn with no route attached | Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows. ## LOM model The cell contributes to the lumped model: | branch | type | nodes | value (estimate at defaults) | |---|---|---|---| | `C_X` | C | island – gnd | estimate=98, unit=fF, estimate_source=analytic: 6 CPW arms (20/20 µm) × 0.874 Xmon Q3D anchor, estimate_kind=analytic, uncertainty=±25% | | `J_X` | JJ | island – gnd | Lj_nH=10, Cj_fF=0 | Nodes: `island`. ## How to use In Python: ```python from quantcore_circuits.designer import Designer d = Designer("demo", box=(0, 0, 7500, 7500)) d.add("U1", "metal:TransmonStar", at=(3750, 3750), a=10) # parameters: see the table above # no directed pin: place it with at= / rot=, or snap it with snap= / to= ``` Pin names go into `d.route(...)` as `INSTANCE.pin`, and into `snap=` / `to=` when placing. From the shell: `qcc components metal:TransmonStar` lists the pins; add `--schema` for the parameters. In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.