# Kinetic-inductance TWPA A kinetic-inductance travelling-wave parametric amplifier: a very long thin-film line whose inductance depends on the current. A DC bias and a pump give three-wave mixing along the line, and periodic loaded cells open a stop band that blocks the pump's third harmonic. The geometry is the NY CREATES layout as ported in twpa-sim (MIT), redrawn as a negative mask on the Quantcore PDK. This chip is dominated by one huge component: a 16-row serpentine of about 50 000 cells with two launches, two pads and two short feeds. The PDK Nb film is far less nonlinear than the source's NbN. ```{image} ../../images/designs/amplifiers/ki_twpa_serpentine.png :alt: The whole ki_twpa_serpentine chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/amplifiers/ki_twpa_serpentine.ipynb` (an older one-cell version is kept as `ki_twpa_serpentine.v1.ipynb`) | | Source | twpa-sim `kit.py` / `KITLayout` (MIT), NY CREATES research layout | | Chip | 7.5 × 7.5 mm Quantcore die (the source's is 5 × 5 mm), sapphire 650 µm | | On the chip | 1 `KiTwpaSerpentine` (16 rows × 55 supercells, 49 950 cells) · 2 bond pads · 2 feeds | | Builds today | yes (layout built on 2026-11-19 in 15 s) | ## How the notebook builds it The amplifier notebooks use six Design segments (die, pads, feed, nonlinear element, routing, whole chip); see [the notebook template](../notebook-template.md). ```{image} ../../images/designs/amplifiers/ki_twpa_serpentine_steps.png :alt: The six layout segments of ki_twpa_serpentine :width: 100% ``` 1. **Die.** The empty die with the QCT frame and the device ID `KITWPA`. 2. **Bond pads.** Input and output pads on the west edge, at the heights of the first and last rows. 3. **Feed lines.** No cell: signal, pump and DC bias share the serpentine's own line; the feeds are drawn in segment 5. 4. **Nonlinear element.** The serpentine: rows of one supercell etch, radial U-turns, and the two launches. 5. **Routing.** Two short 50 Ω feeds from the pads to the launches. 6. **Whole chip.** The `launch` sim group around the serpentine and the saved design. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 16 s). This is an amplifier, so the LOM section gives gain and phase matching, not qubit frequencies. The line's dispersion gives a stop band, and the 3WM coupled-mode gain is read at the pump: | line | pump (GHz) | G at f_p/2 (dB) | max G (dB) | |---|---|---|---| | PDK Nb | no stop band below 12 GHz | - | - | | NbN 20 pH/□ | 8.985 | 14.8 | 14.8 | | twpa-sim v2 | 9.113 | 15.1 | 15.1 | ```{image} ../../images/designs/amplifiers/ki_twpa_serpentine_lom.png :width: 80% :alt: Stop band of the serpentine line ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source · licence: mandalsoumyajit/twpa-sim (MIT): `src/twpa/layout/kit.py`, `KITLayout`, process `kit_nycreates_research.json` (NbN 20 pH/□). Die: 7.5 × 7.5 mm PDK die, PDK frame, sapphire 650 µm, Nb trilayer junctions. Notebook and design: `examples/designs/amplifiers/ki_twpa_serpentine.ipynb` / `.json`. ### Components | instance | catalog ref | key params | notes | |---|---|---|---| | P_IN, P_OUT | `BondPad` | west edge (rows 0 and 15) | | | KIT | `KiTwpaSerpentine` | 16 rows × 55 supercells (24 + 6 + 24 cells, 1.5 µm pitch), turns r 154 µm, 3 supercells per turn: 49 950 cells | | ### Routes | route | from → to | type | |---|---|---| | L_IN | P_IN.a → KIT.a | CPW | | L_OUT | P_OUT.a → KIT.b | CPW | ### LOM node structure one conductor (wire between the pads); ladder from `qcc_ladder` (L_geo + L_s·squares, C per cell) ### Targets (from the source) twpa-sim v2: L 53.8 pH, C 22.3 / 8.4 fF per cell, ≈ 50 Ω, 3WM with DC bias ### Simplifications / PDK differences PDK Nb film (0.116 pH/□): ≈ 6 Ω, weakly nonlinear; NbN shown by a `KineticInductance` override in the analysis only