# Lumped JPAs, two couplings The simplest Josephson parametric amplifier: one junction shunted by a capacitor, a lumped LC mode pumped near resonance. The chip has two of them, one coupled to its line through a series capacitor and one through a shared (tapped) inductance. The layout follows twpa-sim's `jpa` families (MIT) on the Quantcore PDK. This notebook compares two ways of coupling a lumped mode to a 50 Ω line, side by side on one die, each with its own pad. ```{image} ../../images/designs/amplifiers/twpa_sim_jpa.png :alt: The whole twpa_sim_jpa chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/amplifiers/twpa_sim_jpa.ipynb` (an older one-cell version is kept as `twpa_sim_jpa.v1.ipynb`) | | Source | twpa-sim `jpa` and `jpa_inductive` (MIT) | | Chip | 7.5 × 7.5 mm Quantcore die, sapphire 650 µm | | On the chip | 2 `LumpedJpa` (capacitive, inductive) · 1 finger capacitor · 2 bond pads · 2 feeds | | Builds today | yes (layout built on 2026-11-19 in 5 s) | ## How the notebook builds it The amplifier notebooks use six Design segments (die, pads, feed, nonlinear element, routing, whole chip); see [the notebook template](../notebook-template.md). ```{image} ../../images/designs/amplifiers/twpa_sim_jpa_steps.png :alt: The six layout segments of twpa_sim_jpa :width: 100% ``` 1. **Die.** The empty die with the QCT frame and the device ID `LJPA`. 2. **Bond pads.** One pad per JPA: the capacitive one from the west edge, the inductive one from the east edge. 3. **Capacitive feed.** The finger coupling capacitor (12 fingers × 80 µm) and its 50 Ω line. 4. **Nonlinear elements.** The two lumped JPAs, with the junction sized to the PDK limit and tabulated against the source. 5. **Routing.** The inductive JPA's feed, ending on its tap strip. 6. **Whole chip.** The two sim groups (`jpa_c`, `jpa_l`) and the saved design. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 7 s). This is an amplifier, so the LOM section gives gain and phase matching, not qubit frequencies. The chip carries two JPAs, a capacitive and an inductive one: | JPA | f0 (GHz) | κ/2π (MHz) | Q_ext | K/2π (MHz) | |---|---|---|---|---| | capacitive | 6.592 | 40.4 | 163 | 16.8 | | inductive | 6.802 | 95.8 | 71 | 17.9 | The single-mode Kerr model (undepleted pump) gives a peak gain of 20.4 dB at -123.6 dBm. ```{image} ../../images/designs/amplifiers/twpa_sim_jpa_lom.png :width: 80% :alt: Gain of the two JPAs ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source · licence: mandalsoumyajit/twpa-sim (MIT): `src/twpa/layout/generate.py` (families `jpa`, `inductive_coupler`), `examples/layout/jpa*.json`. Die: 7.5 × 7.5 mm PDK die, PDK frame, sapphire 650 µm, Nb trilayer junctions. Notebook and design: `examples/designs/amplifiers/twpa_sim_jpa.ipynb` / `.json`. ### Components | instance | catalog ref | key params | notes | |---|---|---|---| | P_C, P_L | `BondPad` | west / east edge | | | CC | `FingerCapacitorSquare` | 12 fingers × 80 µm | | | JC | `LumpedJpa` | capacitive, snapped to CC.b; 30 fingers/side × 150 µm IDC; PDK max junction | | | JL | `LumpedJpa` | inductive (tap strip 8 µm), rot 180; same IDC and junction | | ### Routes | route | from → to | type | |---|---|---| | L_C | P_C.a → CC.a | CPW | | L_L | P_L.a → JL.signal | CPW | ### LOM node structure JC: island (C_shunt, JJ to ground), then C_c π, then pad; JL: island (C_shunt), then JJ, then tap (L_tap + C_tap to ground, pad) ### Targets (from the source) none stated (illustrative process: f0 ≈ 63 GHz) ### Simplifications / PDK differences planar IDC instead of MIM; PDK junction (0.65 µA) instead of 20 µA; galvanic tapped inductance instead of a pickup loop; junctions are flagged `pdk_rn` where present (amplifier junctions are far below the qubit R_n window).