# Flux-pumped SQUID JPA A lumped JPA whose inductor is a DC SQUID. A static flux tunes the mode, and a pump on the flux line at twice the signal frequency modulates the SQUID (three-wave mixing). The layout follows twpa-sim's `squid_jpa` family (MIT), which leaves the coupling and flux line external; the rebuild draws both. This chip is a small flux-pumped amplifier: a coupling capacitor on the signal side, the SQUID with its shunt capacitor, and a flux line that arrives from a second pad. ```{image} ../../images/designs/amplifiers/twpa_sim_squid_jpa.png :alt: The whole twpa_sim_squid_jpa chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/amplifiers/twpa_sim_squid_jpa.ipynb` (an older one-cell version is kept as `twpa_sim_squid_jpa.v1.ipynb`) | | Source | twpa-sim `squid_jpa` (MIT) | | Chip | 7.5 × 7.5 mm Quantcore die, sapphire 650 µm | | On the chip | 1 `LumpedJpa` with SQUID and flux line · 1 finger capacitor · signal and flux pads | | Builds today | yes (layout built on 2026-11-19 in 5 s) | ## How the notebook builds it The amplifier notebooks use six Design segments (die, pads, feed, nonlinear element, routing, whole chip); see [the notebook template](../notebook-template.md). ```{image} ../../images/designs/amplifiers/twpa_sim_squid_jpa_steps.png :alt: The six layout segments of twpa_sim_squid_jpa :width: 100% ``` 1. **Die.** The empty die with the QCT frame and the device ID `SQJPA`. 2. **Bond pads.** The signal pad on the west edge and the flux / pump pad on the east edge. 3. **Signal feed.** The coupling capacitor (14 fingers × 90 µm) and its 50 Ω line. 4. **Nonlinear element.** The SQUID JPA: the largest PDK SQUID, a shunt capacitor and the flux line. 5. **Routing.** The flux / pump line from the SQUID to the east pad. 6. **Whole chip.** The `jpa` sim group and the saved design. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 7 s). This is an amplifier, so the LOM section gives gain and phase matching, not qubit frequencies. The JPA's resonance is tuned by flux: | Φ (Φ0) | f0 (GHz) | κ/2π (MHz) | Q_ext | K/2π (MHz) | |---|---|---|---|---| | 0 | 6.946 | 42.0 | 166 | 9.34 | | 0.1 | 6.774 | 40.0 | 170 | 9.34 | | 0.2 | 6.247 | 34.2 | 183 | 9.33 | | 0.3 | 5.324 | 25.0 | 213 | 9.33 | | 0.4 | 3.860 | 13.3 | 291 | 9.32 | At 0.3 Φ0 the tuning slope is df0/dΦ = -11.54 GHz/Φ0 with κ/2π = 25.0 MHz. Flux-pumped gain against the pump strength r: | r | peak gain (dB) | pump flux Φ_p (mΦ0) | |---|---|---| | 0.5 | 4.44 | 1.08 | | 0.7 | 9.31 | 1.52 | | 0.8 | 13.2 | 1.73 | | 0.9 | 19.6 | 1.95 | ```{image} ../../images/designs/amplifiers/twpa_sim_squid_jpa_lom.png :width: 80% :alt: Flux-pumped gain of the SQUID JPA ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source · licence: mandalsoumyajit/twpa-sim (MIT): `src/twpa/layout/generate.py` (family `squid_jpa`), `examples/layout/squid_jpa.json`. Die: 7.5 × 7.5 mm PDK die, PDK frame, sapphire 650 µm, Nb trilayer junctions. Notebook and design: `examples/designs/amplifiers/twpa_sim_squid_jpa.ipynb` / `.json`. ### Components | instance | catalog ref | key params | notes | |---|---|---|---| | P_SIG, P_FLUX | `BondPad` | west / east edge | | | CC | `FingerCapacitorSquare` | 14 fingers × 90 µm | | | JS | `LumpedJpa` | Quantcore Squid (2 × 2.0 × 2.0 µm), flux line, 45 fingers/side × 180 µm IDC | | ### Routes | route | from → to | type | |---|---|---| | L_SIG | P_SIG.a → CC.a | CPW | | L_FLUX | JS.flux → P_FLUX.a | CPW, one waypoint | ### LOM node structure island (C_shunt, SQUID to ground at the static bias `flux_phi0`), then C_c π, then pad; flux is a control ### Targets (from the source) none stated (illustrative: f0 ≈ 70 GHz) ### Simplifications / PDK differences PDK SQUID; planar IDC; coupling and flux line drawn (external in the source); junctions are flagged `pdk_rn` where present (amplifier junctions are far below the qubit R_n window).