# Six-Xmon chip (Litho) Six Xmons in two columns of three, one each side of a vertical feedline, each with a λ/4 meander readout coupled to the feedline. The layout is the six-Xmon notebook of Qiskit-Metal-to-Litho (CC BY 4.0), rebuilt on the Quantcore PDK with a trilayer junction per qubit (L_J 15.904 nH). This notebook is an example of a frequency-multiplexed readout on one feedline (six readouts, 6.116 to 6.704 GHz) and of moving a foreign design onto the PDK pad rule. ```{image} ../../images/designs/community/qm2litho_6xmon.png :alt: The whole qm2litho_6xmon chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/community/qm2litho_6xmon.ipynb` (an older one-cell version is kept as `qm2litho_6xmon.v1.ipynb`) | | Source | Qiskit-Metal-to-Litho `6_Xmon_Layout_with_Quantum_Metal_PHIDL_GDSTK_in_Colab.ipynb`, CC BY 4.0 | | Chip | 5 × 5 mm Quantcore die (the source's chip size), feedline 11.7 / 5.1 µm | | On the chip | 2 launchpads · 1 feedline · 6 Xmons · 6 λ/4 hanger readouts | | Builds today | yes (layout built on 2026-11-19 in 23 s) | ## How the notebook builds it ```{image} ../../images/designs/community/qm2litho_6xmon_steps.png :alt: The layout segments of qm2litho_6xmon, one picture each :width: 100% ``` 1. **Die.** The 5 × 5 mm die with the frame and the device ID `QM2L-6X`. 2. **Bond pads.** Two launchpads, moved to the 100 µm pad rule. 3. **Feedline.** A straight 11.7 / 5.1 µm line between the pads. 4. **Qubits.** Six Xmons with trilayer junctions. 5. **Readouts.** Six λ/4 hanger routes from the claws to the feedline. 6. **Coupling.** None: the qubits do not couple to each other. 7. **Control lines.** None. 8. **Whole chip.** Sim groups, targets, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 26 s): QuCat normal modes with QuTiP dressed values. | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---| | Q1_L | 3.183 | -151 | R_Q1_L | 5.431 | 0.0597 | -0.124 | | Q2_L | 3.183 | -151 | R_Q2_L | 5.609 | 0.0655 | -0.117 | | Q3_L | 3.183 | -151 | R_Q3_L | 5.698 | 0.0685 | -0.113 | | Q1_R | 3.183 | -151 | R_Q1_R | 5.769 | 0.071 | -0.111 | | Q2_R | 3.183 | -151 | R_Q2_R | 5.833 | 0.0733 | -0.109 | | Q3_R | 3.183 | -151 | R_Q3_R | 5.869 | 0.0747 | -0.108 | ```{image} ../../images/designs/community/qm2litho_6xmon_lom.png :width: 80% :alt: LOM plot of qm2litho_6xmon ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source: [OJB-Quantum/Qiskit-Metal-to-Litho](https://github.com/OJB-Quantum/Qiskit-Metal-to-Litho), `6_Xmon_Layout_with_Quantum_Metal_PHIDL_GDSTK_in_Colab.ipynb`. Outputs `GDS Files/six_xmon_quantum_metal.gds`, the `_cheesing` variant and `six_xmon_quantum_metal_gaps.oas` (not downloaded). Licence **CC BY 4.0** (verified). Read on 2026-11-02: notebook constants only. What it is: 6 Xmons (`TransmonCross`) in two columns of 3, one each side of a straight vertical feedline. Each has a λ/4 meander readout coupled through a `CoupledLineTee` (6.116–6.704 GHz). It is the same family and parameters as the SQuADDS tutorial-5 qubit (Lj 15.904 nH). A second notebook section adds an antidot (vortex-hole) field. Frame: chip 5 × 5 mm centred. **Box (0, 0, 5000, 5000)**, **Designer = source + (2500, 2500)**. Feedline 11.7/5.1 µm; readout 10/6 µm. Layers 3/0 metal, 3/1 etch, 9 junction. The chip needs `Xmon`, `BondPad` and hangers. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | Q1_L / Q2_L / Q3_L | `Xmon` | cross tip-to-tip 520 (cross_length 260), arm_width 35, gap 20. Claw toward the feedline: claw_length 190, width 10, gap 6, ground spacing 5, claw stub 60 | (800, 4000) / (800, 2500) / (800, 1000) | claw faces +x | Metal orientation −90, source x −1700, y 1500/0/−1500 | | Q1_R / Q2_R / Q3_R | `Xmon` | same | (4200, 4000) / (4200, 2500) / (4200, 1000) | claw faces −x | orientation 90 | | WB_TOP / WB_BOT | `BondPad` (pad 160 × 200, taper 200, pad_gap 58, lead 25, a 11.7, b 5.1) | | (2500, 4600) / (2500, 400) | 180 / 0 | pos_y ±2100 | Junction: `junction={"Lj_nH": 15.9, "Cj_fF": 2}` (Lj 15.903982 nH stated; Cj assumed). ### Routes | route | from → to | type, length | hanger (s, length, side, ground_gap) | f_target | |---|---|---|---|---| | FL | WB_TOP.a → WB_BOT.a | cpw 11.7/5.1 | straight x 2500 (travel −y, left = +x) | | | R_Q1_L | Q1_L.claw → FL.hanger | meander 4905 | s ≈ 4600 − 4000 = 600 (from the pad port), 200, right, **4** | 6.116 | | R_Q2_L | Q2_L.claw → FL.hanger | 4722 | s ≈ 2100, 200, right, 4 | 6.353 | | R_Q3_L | Q3_L.claw → FL.hanger | 4635 | s ≈ 3600, 200, right, 4 | 6.472 | | R_Q1_R | Q1_R.claw → FL.hanger | 4567 | s ≈ 600, 200, left, 4 | 6.568 | | R_Q2_R | Q2_R.claw → FL.hanger | 4508 | s ≈ 2100, 200, left, 4 | 6.655 | | R_Q3_R | Q3_R.claw → FL.hanger | 4475 | s ≈ 3600, 200, left, 4 | 6.704 | L = v/(4f) with v = 1.20e8 m/s. Frequencies are taken in site order (index-matched in the code). CLT: coupling_length 200, coupling_space 4 (ground strip, used as ground_gap), down_length 110. Meander spacing 240, fillet 70, leads 180/140; meander asymmetry ±90 alternates per row. Two hangers share each s (left and right of the line); that works because they sit on opposite sides. ### Launchers, pads, test structures, markers, labels 2 pads. Cheesing variant: antidots 2 µm squares at 10 µm pitch, 15 µm keep-out, 45 µm around pads. Maps to `chip={"with_grid": True}`. ### LOM node structure 6 grounded Xmon islands (fixed JJ). Each has a claw C_g to its λ/4 R, which has κ to FL (two 50 Ω ports). No couplers or control lines. ### Targets Readout 6.116 / 6.353 / 6.472 / 6.568 / 6.655 / 6.704 GHz. Qubit about 3.66 GHz if it matches the SQuADDS DB entry (same cross and Lj; inferred, not stated). ### Simplifications for a first rebuild Build it as is. If two couplers at the same s clash with the Xmon claw approach, offset the right column's s by ±50 µm. ### Build The notebook uses the Metal cells themselves (`metal:TransmonCross`, `metal:LaunchpadWirebond`) instead of `Xmon`/`BondPad`; CLT + meander → one qcc hanger (coupler upper end at the qubit height). Route length = source meander + 310 µm (the tee's coupled and down legs). Box 5.0 × 5.2 mm: the source pads overhang Metal's 5 mm chip by 83 µm.