# One-qubit template (SQChip-EM) The one-qubit template of the SQChip-EM layout-to-EM dataset: a pocket transmon, an interdigital tee and a λ/2 readout feed to one launchpad. The repository states no licence, so treat the page as a reference; the notebook is a Quantcore PDK rebuild (GPL-3.0) of the Qiskit Metal generator `metal_KDD_1qubit.py`. This notebook is an example of the smallest readout chain (qubit, tee, feed, pad) and of the order PDK placement needs: centre the core first, then the pad. ```{image} ../../images/designs/community/sqchip_em.png :alt: The whole sqchip_em chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/community/sqchip_em.ipynb` (an older one-cell version is kept as `sqchip_em.v1.ipynb`) | | Source | `Secbrain/SQChip-EM` `chip_code/metal_KDD_1qubit.py` (licence not stated) | | Chip | 7.5 × 7.5 mm Quantcore die | | On the chip | 1 launchpad · 1 pocket transmon (L_J 12 nH) · 1 interdigital tee · 1 λ/2 readout · 1 feed line | | Builds today | yes (layout built on 2026-11-19 in 7 s) | ## How the notebook builds it ```{image} ../../images/designs/community/sqchip_em_steps.png :alt: The layout segments of sqchip_em, one picture each :width: 100% ``` 1. **Die.** The 7.5 mm die with the frame and the device ID `SQCHIP-1Q`. 2. **Qubit.** The pocket transmon with a trilayer junction (L_J 12 nH). 3. **Readout.** The interdigital tee and the λ/2 readout. 4. **Centre.** The core is centred in the die before the pad is placed. 5. **Bond pad.** The launchpad at the 100 µm pad rule. 6. **Feed.** The 5.5 mm feed meander from the pad to the tee. 7. **Coupling and control.** None: one qubit, no drive or flux line. 8. **Whole chip.** One sim group, targets, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 8 s): QuCat normal modes with QuTiP dressed values. | mode | kind | f (GHz) | κ (MHz) | A (MHz) | participation | |---|---|---|---|---|---| | Q1 | qubit | 5.396 | 1.52 | 252 | J_Q1 0.97, RO_RES 0.03 | | RO_RES | resonator | 6.131 | 93.4 | 0.3 | RO_RES 0.97, J_Q1 0.03 | | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q1R | Q1 | 5.118 | -301 | RO_RES | 6.125 | 93.4 | -8.37 | ```{image} ../../images/designs/community/sqchip_em_lom.png :width: 80% :alt: LOM plot of sqchip_em ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. > The notebook `examples/designs/community/sqchip_em.ipynb` (with its `.json` and PNGs) is the 1-qubit template as a > Quantcore PDK rebuild, distributed under GPL. The `metal:` references in this spec build as written, through the `metal:` wrapper (ports are the Metal pin names, parameters the Metal options); the Quantcore and KQC substitutions are optional. Source: [Secbrain/SQChip-EM](https://github.com/Secbrain/SQChip-EM) (dataset DOI 10.5281/zenodo.20489133, per the README badge). **Licence: not stated.** There is no LICENSE file and no licence section in the README, so treat it as all rights reserved and use for reference only. Read on 2026-11-02: README, `chip_code/metal_KDD_1qubit.py` (`LayoutParams`, `populate_design`), `data/sqchip_em_{1q,2q}/summary.csv`. The 3342 JSON/GDS records and the 3–8 qubit generators (1.2k–5.8k lines each) were not read in detail. What it is: an ML benchmark linking parameterised Metal layouts to HFSS eigenmode (pyEPR) and Q3D LOM results. Public data covers 1-qubit (532 rows) and 2-qubit (35 rows) splits. The 3/4/6/8q folders are empty placeholders. README renders exist for 2, 3, 4, 5, 6, 8-qubit chips (`figure/final_*q_ro_res_bus.png`). The chip uses `metal:TransmonPocket` and `metal:CapNInterdigitalTee`. The source is a reference only. ### 1-qubit template (`metal_KDD_1qubit.py`) Frame: chip 12 × 12 mm centred. **Designer = source + (6000, 6000)**. CPW 10/6. | instance | catalog ref | key params (units) | at (source, mm) | notes | |---|---|---|---|---| | Q1 | `metal:TransmonPocket` · stand-in `DoublePads` | pad_width 520, pocket_height 780. Readout pad (loc_W +1, loc_H +1) 180 × 150, gap 1.4 µm (sweep default) | (dx, dy), swept −10…+10 mm (24 values each) | `hfss_inductance` = Lj variable | | RO_TEE | `metal:CapNInterdigitalTee` · stand-in `FingerCapacitorSquare` + a tee | prime 14/6, second 10/6, finger_count **12**, finger_length **160**, cap_gap **1.2**, cap_width 8, cap_distance 220 | readout pin + (1.0, 2.0) mm | readout resonator couples to the feedline through an interdigital tee | | LP_RO | `metal:LaunchpadWirebond` / `BondPad` | | tee − (2.4, 0) mm | | | RO_FEED | route LP_RO.tie → RO_TEE.prime_start | meander 5.5 mm, spacing 280, leads 250/250, fillet 25 | | feedline (one launcher; prime_end is not routed) | | RO_RES | route RO_TEE.second_end → Q1.readout | meander **8.5 mm** (ro_L), spacing 260, leads 250/250 | | capacitive at both ends (λ/2 type) | 1q dataset values: Lj 12 nH, Cj 2 fF. f_q 4.60–4.83 GHz, f_r 5.73–6.26 GHz, g/2π 200–294 MHz, χ 4.7–7.8 MHz, κ/2π 5.3–6.1 MHz, C_in ≈ 52 fF. Only the qubit position varies across the 532 rows. ### 2-qubit split (summary only) Q1 at (−1.5…0, 0…1.5) mm, Q2 at (0…2, −1.5…2) mm. Lj 3 or 12 nH, ro_L 8.5–9 mm, the same tee. Readouts, a bus and a resonator per qubit (render `final_2q_ro_res_bus.png`). Many rows are unphysical (f_q 1.7–22.6 GHz, g up to 8.4 GHz), so filter on `status`. ### LOM node structure 1q: floating pocket transmon (2 pad nodes + JJ) → readout pad C_g → RO_RES (λ/2, 8.5 mm) → interdigital C_in ≈ 52 fF → feedline → one 50 Ω port. N-qubit: same per qubit, plus buses (`ro_res_bus` renders). ### Simplifications for a first rebuild 1. The 1q record serves as a LOM cross-check rather than a rebuild target: our `DoublePads` + λ/2 route + finger capacitor should land near f_r ≈ 6 GHz and g ≈ 0.2–0.3 GHz for Lj 12 nH. ### Rebuild (Quantcore PDK) - **Frame and stack:** the PDK 7.5 mm die (device ID `SQCHIP-1Q`; the source's 12 mm canvas is mostly empty) and the PDK stack (sapphire). - **Cells:** `metal:TransmonPocket` (pads 520 µm, pocket height 780 µm, readout pad 180 × 150 µm, gap 1.4 µm) and `metal:CapNInterdigitalTee` (prime 14/6, second 10/6, 12 fingers × 160 µm, gap 1.2, cap distance 220), at the source's offsets: tee = readout pin + (1.0, 2.0) mm, launchpad = tee − (2.4, 0) mm. - **Routes:** qcc meanders of the source's lengths, 5.5 mm feed and 8.5 mm λ/2 readout. The tee's `prime_end` is left open, as in the source. - **Junction:** `Quantcore Junction` at the dataset's L_J = 12 nH (`registry.trilayer_junction(..., lj_nH=12)`). - **Quick check** (script run of the cells, not nbclient): - DRC: 0 errors, 3 `dangling_port` (squid_a/b, the open `prime_end`); - LOM: 4 nodes; - LOM sim: f_q 5.12 GHz against the dataset's 4.734 (the LOM C_Σ is lower than HFSS); f_r 6.22 GHz against 6.099 (sapphire vs Si); χ −7.35 MHz against 4.7–7.8; κ 94.5 MHz against 5.3–6.1. κ is far too large: the LOM's IDC estimate for 12 × 160 µm fingers at a 1.2 µm gap gives C_in well above the dataset's ≈ 52 fF (a limit of the LOM's IDC model). - **FEM:** the q3d and eigenmode jobs `Q1R` have nets `Q1.island1/2`.