# DeviceLayout SingleTransmon A single grounded rectangular transmon island read out through a λ/4 meander that ends in a claw. The meander is coupled to a straight feedline over 400 µm and is shorted at the far end. It is the DeviceLayout.jl `SingleTransmon` example (AWS, MIT), built there as a Palace eigenmode model, and is rebuilt here on the Quantcore PDK (the rebuild is distributed under GPL-3.0). This is the smallest complete readout: a feedline between two pads, one qubit with a claw, and one hanger resonator. The junction is re-sized for 4.05 GHz because the source's 3.37 GHz is below the PDK band. ```{image} ../../images/designs/devicelayout/singletransmon.png :alt: The whole singletransmon chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/devicelayout/singletransmon.ipynb` (an older one-cell version is kept as `singletransmon.v1.ipynb`) | | Source | DeviceLayout.jl `examples/SingleTransmon` (MIT, © Amazon.com, Inc. or its affiliates) | | Chip | 7.5 × 7.5 mm Quantcore die (the source's domain is 4 × 3.7 mm), sapphire 650 µm | | On the chip | 1 Swissmon qubit · 1 λ/4 readout · 1 feedline · 2 bond pads | | Builds today | yes (layout built on 2026-11-19 in 4 s) | ## How the notebook builds it Each Design segment is one cell with a picture of the chip so far (see [the notebook template](../notebook-template.md)). ```{image} ../../images/designs/devicelayout/singletransmon_steps.png :alt: The layout segments of singletransmon :width: 100% ``` 1. **Die.** The 7.5 mm die around the source's simulation domain, with the QCT frame. 2. **Bond pads.** Two small pads that end the feedline (the source has lumped ports there). 3. **Feedline.** A straight 10 / 6 µm line between the pads. 4. **Qubit.** The Swissmon island and the junction sized for 4.05 GHz. 5. **Readout.** The clawed λ/4 resonator, hung on the feedline with a 5 µm ground strip. 6. **Coupling.** None: there is one qubit. 7. **Routing.** None: the source qubit has no drive or flux line. 8. **Whole chip.** The Palace targets, the sim group, centring and the save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 6 s): QuCat normal modes with QuTiP dressed values. | mode | kind | f (GHz) | κ (MHz) | A (MHz) | participation | |---|---|---|---|---|---| | Q | qubit | 4.373 | 0.000122 | 258 | J_Q 1.00 | | R | resonator | 5.684 | 0.224 | 0 | R 1.00 | | parameter | LOM (QuTiP) | target | |---|---|---| | `Q.f_q_GHz` | 4.1 | 3.37 | | `Q.alpha_MHz` | -307 | – | | `R.chi_MHz` | -0.708 | – | | `R.f_GHz` | 5.68 | 5.24 | | `R.kappa_MHz` | 0.224 | – | ```{image} ../../images/designs/devicelayout/singletransmon_lom.png :width: 80% :alt: LOM plot of singletransmon ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source: [examples/SingleTransmon/SingleTransmon.jl](https://github.com/aws-cqc/DeviceLayout.jl/blob/main/examples/SingleTransmon/SingleTransmon.jl) and docs page `docs/src/examples/singletransmon.md` ([rendered](https://aws-cqc.github.io/DeviceLayout.jl/stable/examples/singletransmon/)) · components from `src/schematics/ExamplePDK` (`ExampleRectangleTransmon`, `ExampleClawedMeanderReadout`) · licence MIT ("Copyright Amazon.com, Inc. or its affiliates", `LICENSE.md`, verified) · Read on 2026-11-02 (Julia, not run). What it is: a grounded rectangular transmon island read out by a λ/4 meander. The meander is shorted at its coupled section, which runs 400 µm alongside a straight 2700 µm feedline, and ends in a claw that wraps the island. Built as a Palace eigenmode model: lumped ports at both feedline ends, airbridges every 300 µm. Frame: the simulation domain is 4.0 × 3.7 mm (`substrate_x`, `substrate_y`), centred on the floorplan. The feedline runs vertically (α0 = 90°) from (0, 0) to (0, 2700) in the source, with the resonator on its right (+x). Our estimated floorplan centre is (1130, 1350), so **box (0, 0, 4000, 3700)** and **Designer ≈ source + (870, 500)**. The feedline is then at x 870, y 500…3200. Substrate: sapphire (Palace config εr 9.3/9.3/11.5, tan δ 3e-5/8.6e-5). CPW 10/6 µm, bend radius 50 µm. A `Swissmon` stands in for the rectangle island (Swissmon has a LOM model). ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | P_S / P_N | `BondPad` (small: pad_width 200, pad_height 200, taper_length 150, pad_gap 50) | the source has no pads, only lumped ports at the line ends | (870, 300) / (870, 3400) | 0 (faces N) / 180 (faces S) | or keep the box and accept pads overlapping the domain edge | | Q | `Swissmon` (stand-in for `ExampleRectangleTransmon`) | island 24 × 620 µm (cap_width × cap_length), cap_gap 30, junction_gap 12. Swissmon: arm_length [12, 298, 12, 298] (WNES), arm_width 24, gap_width [30, 30, 30, 12] | ≈ (2685, 1850) | 90 (N arm and claw face the feedline, −x) | island centre ≈ 1815 µm right of the feedline (estimate ±50) | | (claw) | Swissmon N coupler | claw_trace 34 → cpl_width 34, claw_length 121 → cpl_length 121, claw_gap 6 → cpl_b 6, grasp_width 84 → cpl_gap 84, shield_width 2 | on Q.cplr1 | — | `ExampleClawedMeanderReadout` claw | Junction: lumped element in Palace, **Lj = 14.860 nH, C = 5.5 fF**, so `junction={"Lj_nH": 14.86, "Cj_fF": 5.5}`. ### Routes | route | from → to | type, length | hanger | notes | |---|---|---|---|---| | FL | P_S.a → P_N.a | cpw 10/6 | straight x 870 (2700 µm between the source port positions) | `p_ro` | | R | Q.cplr1 → FL.hanger | meander **5000** | s = midpoint (y 1850, i.e. s ≈ 1350 + pad offset), length **400**, side **right** (+x when travelling +y), ground_gap **5** | λ/4. Short at the far end of the coupled section, then a 500 µm `hanger_length` leg, 5 meander turns (r 50), a 428 µm arm, and the claw | Total y extent from the feedline to the claw hook: 428 + 5 + 11 + 500 + (3 + 2·5)·50 = **1594 µm**. Airbridges: `add_bridges!(…, spacing=300 µm)` on all paths, so use `airbridges=` on FL and R. ### Launchers, pads, test structures, markers, labels None in the source (lumped ports only). Optional wave-port variant: readout length 4 mm, touching the domain boundary. ### LOM node structure Q: grounded island (C_Σ + Lj 14.86 nH ∥ 5.5 fF to ground) → claw C_g → R (λ/4 CPW, 5000 µm) → coupled-line κ (400 µm, 5 µm ground strip) → FL (two 50 Ω ports). No control lines. ### Targets (stated) Palace eigenmodes with defaults (cap_length 620, total_length 5000): **3.370 GHz** (qubit) and **5.244 GHz** (resonator). The docs' optimisation example retargets to [3.0, 4.0] GHz by varying cap_length and total_length, and reaches [3.005, 3.982] GHz. ### Simplifications for a first rebuild 1. Swissmon with short W/E stubs stands in for the rectangular island. A dedicated `ExampleRectangleTransmon` (grounded rectangle with end claw) would be exact. `Xmon` also works (cross_length 620, but it has a cross). 2. Exact claw shield (2 µm ground shield between claw and island pocket) is optional. 3. Pads are not in the source. With the 3.7 mm box, use small pads or `launchers=None` and treat the line ends as ports in simulation. ### Build The notebook is `examples/designs/devicelayout/singletransmon.ipynb`. It uses the Swissmon stand-in (arm_length [12, 298, 12, 298], N-arm claw 121/34/84). Island at (2685, 2050), coupled section y 1650–2050 (s 1350, backward, short at the south end). Airbridges omitted: KQC auto bridges landed on the neighbouring coupled line. LOM 4.51 / 5.78 GHz vs Palace 3.370 / 5.244 GHz. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild, not a replica: the netlist, LOM and imported components are kept, the process is Quantcore's. Notebook: [`examples/designs/devicelayout/singletransmon.ipynb`](../../../examples/designs/devicelayout/singletransmon.ipynb). - **Chip:** the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 4 × 3.7 mm Palace domain is centred in it (`box=(-1750, -1900, 5750, 5600)`), so every coordinate stays the source's. - **Stack:** sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); the Palace model uses sapphire with εr 9.3 / 9.3 / 11.5. - **Junctions:** Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). A single junction, as in the source. Its target f_q 3.37 GHz is below the PDK band (4–8 GHz), so the junction is **sized for 4.05 GHz** with the LOM C_Σ of the first build (≈ 70 fF): straight finger 0.19 µm (KQC's `junction_width`) × 0.6 µm, L_J ≈ 17.7 nH, C_J ≈ 5.7 fF, so **R_n ≈ 121 kΩ, above the 40–50 kΩ window** (a 45 kΩ junction would put it at ≈ 6.4 GHz, above the 5.24 GHz readout). The targets stay the source's. - **Kept:** the topology (rectangle island, clawed λ/4, straight feedline), the 5000 µm readout with its 400 µm coupled section, the claw and island geometry, the targets, the sim group.