# Google coupler cell The two-qubit unit of Google's Sycamore processor: two frequency-tunable Xmon-type transmons joined by a third, flux-tunable transmon (the coupler). Tuning the coupler moves the qubit-qubit coupling from tens of MHz (for gates) through zero (idle). Each qubit has a λ/4 readout on a shared feedline, an XY line and a Z line. No Sycamore layout is public; the papers give the targets, and the layout is ours (GPL). This notebook lays out the tunable-coupler scheme on a chip: three crosses in a row with trilayer SQUIDs, hanger readouts on one feedline, and flux lines. ```{image} ../../images/designs/google/google_tc_cell.png :alt: The whole google_tc_cell chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/google/google_tc_cell.ipynb` (an older one-cell version is kept as `google_tc_cell.v1.ipynb`) | | Source | Arute et al., Nature 574, 505 (2019); Yan et al., PR Applied 10, 054062 (2018); no public layout | | Chip | 7.5 × 7.5 mm Quantcore die, sapphire 650 µm (εr 10.25), CPW 10 / 6 µm | | On the chip | 2 qubits · 1 coupler · 2 λ/4 hangers · 1 feedline · 7 bond pads | | Builds today | yes (layout built on 2026-11-19 in 9 s) | ## How the notebook builds it Each Design segment is one cell with a picture of the chip so far (see [the notebook template](../notebook-template.md)). ```{image} ../../images/designs/google/google_tc_cell_steps.png :alt: The layout segments of google_tc_cell :width: 100% ``` 1. **Die.** The empty 7.5 mm die with the QCT frame and the device ID `GTC2Q`. 2. **Bond pads.** Seven pads: two for the feedline, two for XY lines, three for Z lines. 3. **Feedline.** A straight 10 / 6 µm line between its pads. 4. **Qubits.** Two Xmon crosses with Quantcore trilayer SQUIDs (L_J 6.1 nH). 5. **Readouts.** Two λ/4 readouts, each ending in a 900 µm hanger on the feedline. 6. **Coupling.** The smaller coupler cross between the qubits and the declared capacitances. 7. **Control lines.** The XY lines and the Z lines to the south pads. 8. **Whole chip.** Centring in the die, targets, sim groups and the save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 87 s): QuCat normal modes with QuTiP dressed values. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q1+R1 | Q1 | 6.668 | -236 | R1 | 4.505 | 0.671 | -0.177 | | Q2+R2 | Q2 | 6.668 | -236 | R2 | 4.585 | 0.705 | -0.202 | | L_J,c (nH) | Φ/Φ0 | f_c (GHz) | α_c (MHz) | f_q1 (GHz) | f_q2 (GHz) | 2·abs(g̃) (MHz) | g̃ (MHz) | g̃ Yan Eq. 5 (MHz) | ZZ (kHz), q2 detuned | |---|---|---|---|---|---|---|---|---|---| | 6 | 0 | 8.765 | -424 | 6.567 | 6.577 | 10 | 5.01 | 5.1 | -200 | | 6.25 | 0.09 | 8.581 | -424 | 6.567 | 6.576 | 8.93 | 4.47 | 4.57 | -177 | | 6.5 | 0.126 | 8.408 | -423 | 6.567 | 6.575 | 7.7 | 3.85 | 3.98 | -155 | | 6.75 | 0.151 | 8.244 | -422 | 6.567 | 6.573 | 6.3 | 3.15 | 3.3 | -133 | | 7 | 0.172 | 8.09 | -421 | 6.567 | 6.572 | 4.7 | 2.35 | 2.53 | -114 | | 7.25 | 0.19 | 7.944 | -418 | 6.567 | 6.57 | 2.84 | 1.42 | 1.64 | -97.9 | | 7.5 | 0.205 | 7.806 | -414 | 6.567 | 6.568 | 0.664 | 0.332 | 0.614 | -89.1 | | 7.75 | 0.218 | 7.675 | -408 | 6.567 | 6.565 | 1.91 | -0.955 | -0.596 | -92 | | 8 | 0.23 | 7.551 | -400 | 6.562 | 6.567 | 5 | -2.5 | -2.03 | -115 | | 8.5 | 0.251 | 7.322 | -367 | 6.554 | 6.567 | 13.5 | -6.73 | -5.87 | -296 | | 9 | 0.268 | 7.118 | -302 | 6.54 | 6.567 | 27.2 | -13.6 | -11.7 | -1030 | | 9.25 | 0.275 | 7.027 | -256 | 6.53 | 6.567 | 37.5 | -18.8 | -15.8 | -2060 | | 9.5 | 0.282 | 6.943 | -207 | 6.515 | 6.567 | 51.7 | -25.9 | -20.9 | -4400 | | 9.75 | 0.289 | 6.868 | -159 | 6.496 | 6.567 | 71.5 | -35.7 | -26.9 | -10300 | | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | cell, coupler off | Q2 | 6.118 | -194 | R1 | 4.505 | 0.671 | -0.175 | | cell, coupler on | Q2 | 6.112 | -190 | R1 | 4.505 | 0.671 | -0.164 | | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | cell, coupler off | Q1-Q2 | -82.5 | yes | no | | cell, coupler off | Q2-TC | -7050 | yes | no | | cell, coupler off | Q1-TC | -15200 | yes | no | | cell, coupler on | Q1-Q2 | -1830 | yes | no | | cell, coupler on | Q2-TC | -27000 | yes | no | | cell, coupler on | Q1-TC | -111000 | yes | no | ```{image} ../../images/designs/google/google_tc_cell_lom.png :width: 80% :alt: LOM plot of google_tc_cell ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. **Sources.** Arute et al., "Quantum supremacy using a programmable superconducting processor", Nature 574, 505 (2019), supplementary information (arXiv:1910.11333): §I "a capacitor-coupled design", g tunable from +5 MHz to −40 MHz, "on" coupling ≈ −20 MHz; §II transmon qubits (DC SQUID), 88 couplers, two bump-bonded dies; §III XY + Z lines per qubit, a Z line per coupler, λ/4 readouts multiplexed on Purcell-filtered lines; Table 2 medians: f_max 6.924 GHz, idle 6.661 GHz, η −208.0 MHz, readout drive 4.618 GHz, κ 0.64 MHz, g_qr 72.3 MHz. Yan et al., "A tunable coupling scheme for implementing high-fidelity two-qubit gates", PR Applied 10, 054062 (2018) (arXiv:1803.09813; local copy `build/external/yan2018/`): the Q–C–Q circuit of Fig. 2a (C1 70, C2 72, Cc 200, C1c 4, C2c 4.2, C12 0.1 fF, qubits 4 GHz), the off point of Fig. 2b, Eq. (5) for g̃. **Licence.** Papers cited for parameters only; no layout of Sycamore is published (searched GitHub, Qiskit Metal, SQuADDS, KQC and Google Quantum AI repositories; Cirq publishes the device graph only). Layout and code: ours, GPL. **What it is.** Two flux-tunable grounded transmons (Xmon-type crosses) and a flux-tunable grounded transmon coupler between them, end-on capacitive coupling of the arm tips; per qubit a λ/4 readout on one feedline, an XY drive line ending open at the outer arm tip and a Z line; a Z line on the coupler. **Chip.** PDK standard die 7.5 × 7.5 mm, Quantcore die frame (QCT), device ID `GTC2Q`; sapphire 650 µm, εr 10.25; 10/6 µm CPW. Junctions: Quantcore trilayer SQUIDs (`junction_type="Quantcore Squid"`), drawn L_J 6.01 nH at zero flux (R_n ≈ 40.2 kΩ, C_J 16.8 fF). **Notebook.** `examples/designs/google/google_tc_cell.ipynb`, built from metal:TransmonCrossFL with a Quantcore trilayer substitution, BondPad and OpenToGround. ### Components | instance | catalog ref | key params (µm) | at (x, y) | rot | notes | |---|---|---|---|---|---| | Q1, Q2 | metal:TransmonCrossFL | cross_length 160, cross_width 30, cross_gap 30; claw `readout` at 90° (claw_length 130, width 30, gap 4, ground_spacing 3); flux line | (3750 ∓ 330, 3400) | 0 | Quantcore Squid, L_J 6.01 nH | | TC | metal:TransmonCrossFL | cross_length 70, cross_width 20, cross_gap 20; no claws; flux line | (3750, 3400) | 0 | the coupler; Quantcore Squid, L_J 6.01 nH (zero flux) | | XY1_end, XY2_end | metal:OpenToGround | width 10, gap 6 | 26 µm beyond the outer pocket edge | 0 / 180 | XY drive ends (20 µm ground to the pocket) | | FL_in, FL_out, XY1, XY2, Z1, ZC, Z2 | BondPad | 400 × 450, taper 450 | edges (see notebook) | | Quantcore pads | ### Routes | route | from → to | type, length | waypoints / hanger | notes | |---|---|---|---|---| | FL | FL_in.a → FL_out.a | cpw, 5200 µm | straight at y = 5500 | feedline | | R1, R2 | Q.readout → FL hanger | meander 6215 / 6095 µm | hanger s = 1450 / 3750, length 900, side right, ground_gap 4, short | λ/4 readouts 4.58 / 4.66 GHz | | XY1_line, XY2_line | XY pad → XY end | cpw | straight | 50 Ω drive lines | | Z1_line, ZC_line, Z2_line | flux_line → Z pad | cpw 5/3 → 10/6 | via y = 2400 | flux bias (controls) | ### LOM node structure Q1 island —(C_QC 2.35 fF)— TC island —(C_QC)— Q2 island, plus Q1 —(C_QQ 0.28 fF)— Q2; each island has a SQUID to ground; Q claw node → R (λ/4 TLres) → HANGER → FL (50 Ω both ends); XY ends → 50 Ω ports; Z lines → `flux_bias` controls. C_QC and C_QQ are `d.couple` estimates (CPS, end-on; C_QQ screened by the coupler, factor 0.15): the Q3D job `core` replaces them. ### Targets | quantity | source | rebuild (LOM) | |---|---|---| | f_q | 6.661 GHz idle (f_max 6.924) | 6.668 GHz alone; 6.57 GHz with the coupler at its off point | | α | −208 MHz | −237 MHz alone; −193 MHz in the full cell | | f_r | 4.618 GHz median | R1 4.577, R2 4.657 GHz | | κ | 0.64 MHz | 0.68 / 0.72 MHz | | g_qr | 72.3 MHz (χ ≈ −0.58 MHz) | χ −0.20 / −0.23 MHz (g ≈ 45 MHz: claw limited by the arm length) | | g̃ range | +5 … −40 MHz, on ≈ −20 MHz | +5.0 MHz at f_c,max 8.77 GHz, 0 at 7.77 GHz, −18.8 MHz at 7.03 GHz, −35.7 MHz at 6.87 GHz | | static ZZ | – | −82 kHz at the off point, −1.8 MHz at the on point (qubits 0.45 GHz apart) | ### Simplifications / adaptations - Planar single die (Sycamore: qubit die bump-bonded to a wiring die); no Purcell filter. - α larger than Sycamore's for an isolated qubit: the PDK window R_n ≥ 40 kΩ caps E_J at f_q ≈ 6.7 GHz. - The off point and g̃ range follow from the capacitances of cell 1 (C_QQ sets the off point): FEM must confirm.