# 3X SQUID cell (chip_10a) Not a full chip but one SQUID cell: two small Nb trilayer junctions side by side in one loop (0.2 µm fingers, windows 16 µm apart). A SQUID like this makes a qubit tunable by flux. The legacy script was unfinished and drew only a pair of fingers; the rebuild completes the cell the way the script's commented-out lines intended. It comes from Quantcore's QWri script `chip_10a_3X_SQUID.py` (internal, used for the chip_05 SQUIDs). The rebuild places the cell in the middle of an otherwise empty PDK die with the device ID `CHIP10A 3X`. Build it to see a junction-sized structure (tens of µm) inside a 7.5 mm die. The whole-chip picture is nearly empty, so use the close-up. ```{image} ../../images/designs/legacy/chip_10a_3x_squid.png :alt: The whole chip_10a_3x_squid die: the cell is the speck at the centre :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/legacy/chip_10a_3x_squid.ipynb` (design JSON `chip_10a_3x_squid.json`) | | Source | Quantcore legacy QWri script `components/python/chip_10a_3X_SQUID.py` (internal) | | Chip | 7.5 × 7.5 mm Quantcore die, sapphire | | On the chip | 1 `TrilayerSquidHSQ` cell (two 0.2 µm junctions) · 2 `JJFingerStraight` fingers | | Builds today | yes, rebuilt from its JSON on 2026-11-19 in 0.9 s (the notebook itself was not re-run) | ## Pictures ```{figure} ../../images/designs/legacy/chip_10a_3x_squid_legacy.png :alt: Legacy chip_10a_3x_squid output :width: 40% What the legacy script actually drew: only the two straight fingers (render of the legacy GDS). ``` ```{figure} ../../images/designs/legacy/chip_10a_3x_squid_squidclose.png :alt: Zoom on the SQUID cell :width: 45% The rebuilt SQUID cell, about 56 µm wide: two junction sites 16 µm apart, both fed from one lead above. ``` ## LOM estimates The notebook has no saved LOM output. The chip has no qubit or resonator, so its LOM netlist is empty. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, the changes made while rebuilding, and the notes. Source: `components/python/chip_10a_3X_SQUID.py` (`create_squid(js=1.0, secondFinger=0, path=...)`, writes `squid_3x_SQ_.gds`; `__main__` calls `create_squid(2)`). Legacy QWri library, Quantcore internal (header: "THIS FILE IS USED FOR CHIP_05 SQUIDS"). Notebook `examples/designs/legacy/chip_10a_3x_squid.ipynb`. ### Changes made in the rebuild - Completed: `SQ` = `TrilayerSquidHSQ` (0.1·js = 0.2 µm straight × 0.2 µm bent at x = ±8 µm, 32 × 20 µm windows, HSQ + gradient) at the die centre, as in the script's commented-out insertions; the drawn positive `top_finger` pair moved 100 µm up (it would sit in the left window). PDK junction rule (Nb trilayer, Δ = 1.4 meV, I_c·R_n = πΔ/2e = 2.20 mV, R_n 40–50 kΩ, qubits 4–8 GHz; PDK process `get_pdk().junction`: R_n·A 13.5 kΩ·µm², C_J 50 fF/µm², both assumed by the PDK): 337.5 kΩ per junction, 168.75 kΩ parallel (L_J 25 nH). - The notebook's JSON was rebuilt from its layout cell. The notebook has not been re-run, so its outputs are cleared and its PNGs may be out of date. What it is: a work-in-progress SQUID junction generator, not a chip. Of everything it sets up (three `JJ_finger Top` / `JJ_finger Bottom` pairs, negative 32 × 20 µm windows at x = ±8 µm, HSQ boxes, the merge into `JUNC_`), only one thing is drawn: cell `top_finger` holds two positive straight fingers (`JJ_finger Top`, `negative=False`, window 0.5 × 0.5 µm, finger length 0.8 µm, x = 8, y = 0, finger width 0.4 µm, pad width 1.0 µm; `conn_height=0.4` is not a parameter of that PCell). Every insertion into `bottom_finger` and `JUNC_`, the HSQ boxes and the final merge are commented out, so `JUNC_2` and `bottom_finger` are written empty. The output is three top cells; only `top_finger` has geometry (2/0, 6.96 µm²). Builds: yes. `JJFingerStraight` (components; golden `test_jj_finger_straight[top3]` covers this parameter set). ### Components (legacy frame, cell `top_finger`) | instance | legacy cell → catalog ref | params | at | notes | |---|---|---|---|---| | FA | `JJ_finger Top` → `JJFingerStraight` | `negative=False, window_width=0.5, window_height=0.5, finger_length=0.8, x=8, y=0, finger_width=0.4, pad_width=1.0` | `Trans(0, True, −15, −5)` → Designer (3735, 3745), mirror | the PCell's own `x=8` offset does not move a positive finger | | FB | same | same | `Trans(2, True, −15, +5)` → Designer (3735, 3755), rot 180°, mirror | | Never drawn (computed, then commented out): bottom (negative) fingers 0.1·js = 0.2 µm wide (`finger_length` 3.2, window 32 × 20, x = ±8, y = −3.6), bent fingers `secondFinger` or 0.1·js = 0.2 µm (`finger_length` 3, window 32 × 19, y = −2), HSQ boxes 0.2 µm wide with a 30 nm overlap: the intended SQUID is two 0.2 × 0.2 µm junctions at x = ±8 µm. No die in the source (it writes the bare cells). Rebuilt on the PDK v2 die frame, the cell at the die centre, with the device ID `CHIP10A 3X`. ### Routes, LOM No routes, no pads, no ports: the LOM netlist is empty. "LOM simulation" = a junction table of the *intended* (undrawn) junctions: 0.2 × 0.2 µm² single and as a two-junction SQUID, with an assumed Jc. No sim groups. ### Keep-outs None.