# Seven Xmons and eight resonators (chip_10a) A qubit chip. One feedline crosses the die, eight λ/4 readout resonators hang off it (four above, four below), and seven Xmon qubits sit at the resonators' open ends, each end wrapped around a qubit's claw. Two of the Xmons are SQUID qubits that can be tuned with flux; their flux lines come in from two small pads at the top and bottom edge. Small test-junction blocks (labelled 500NM and 800NM), flux-trap holes and the label QCG_NB11_W fill the rest. It was made to measure qubit and resonator frequencies, the coupling between them, and the flux tuning. It comes from Quantcore's QWri script `chip_10a_flux_TLQubits.py` (internal), the revision of chip_05 with new junction scripts, new test pads and a finer flux line. The rebuild is in the PDK die frame (device ID `CHIP10A`), with junctions on the PDK junction rule and pads on the 100 µm rule. The PDK cheese (5 µm squares with 20 µm gaps, at least 4 µm from the 3/0 keep-outs) also covers the whole die, and the holes drawn in the original layout stay. Build it to see a full qubit chip: claws on resonator tails, flux lines and test junctions on one die. ```{image} ../../images/designs/legacy/chip_10a_flux_tlqubits.png :alt: The whole chip_10a_flux_tlqubits chip rebuilt on the Quantcore PDK :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/legacy/chip_10a_flux_tlqubits.ipynb` (design JSON `chip_10a_flux_tlqubits.json`) | | Source | Quantcore legacy QWri script `components/python/chip_10a_flux_TLQubits.py` (internal), revision of chip_05 | | Chip | 7.5 × 7.5 mm Quantcore die, sapphire, CPW 10 / 6 µm | | On the chip | 7 Xmons (2 flux-tunable SQUIDs) · 8 λ/4 resonators · 1 feedline with 2 bond pads · 2 flux pads and flux lines · 8 test-pad blocks | | Builds today | yes, rebuilt from its JSON on 2026-11-19 in 2.6 s (the notebook itself was not re-run) | ## Pictures ```{figure} ../../images/designs/legacy/chip_10a_flux_tlqubits_legacy_1000.png :alt: Legacy chip_10a_flux_tlqubits layout :width: 45% The original legacy layout (render of the legacy GDS). ``` ```{figure} ../../images/designs/legacy/chip_10a_flux_tlqubits.png :alt: Rebuilt chip_10a_flux_tlqubits :width: 100% The rebuild: qubits at the resonator ends, flux pads at the top and bottom centre, test-pad blocks in two corners. ``` ```{figure} ../../images/designs/legacy/chip_10a_flux_tlqubits_q1.png :alt: Zoom on qubit Q1 :width: 45% Q1: an Xmon cross with the resonator's claw around its top arm; the junction is at the bottom end. ``` ```{figure} ../../images/designs/legacy/chip_10a_flux_tlqubits_q4.png :alt: Zoom on qubit Q4 :width: 45% Q4, a SQUID qubit: the claw at the bottom, the flux line arriving at the top. ``` ```{figure} ../../images/designs/legacy/chip_10a_flux_tlqubits_pft.png :alt: Zoom on the top flux pad :width: 45% The top flux pad narrowing into the flux line that runs down to Q4. ``` ## LOM estimates The notebook's saved LOM table (QuCat normal modes). Target resonator frequencies from the legacy plan are in brackets. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) (target) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q1+R1 | Q1 | 5.8776 | -365.7 | R1 | 5.7634 (6.5) | 0.146 | 101 | | Q2+R2 | Q2 | 5.8242 | -121.8 | R2 | 5.6272 (6.25) | 0.143 | 75.2 | | Q3+R3 | Q3 | 5.7949 | -197.2 | R3 | 4.9722 (5.5) | 0.101 | -1.98 | | Q4+R4 | Q4 | 7.7695 | -170.3 | R4 | 4.7226 (5.0) | 0.0883 | -0.0543 | | Q5+R5 | Q5 | 7.7506 | -169.3 | R5 | 5.3035 (6.0) | 0.122 | -0.159 | | Q6+R6 | Q6 | 6.0567 | -121.7 | R6 | 6.34 (7.2) | 0.179 | -7.76 | | R7+Q7 cross | – | – | – | R7 | 4.8406 (5.25) | 0.0948 | – | | R8 | – | – | – | R8 | 6.9626 (7.0) | 0.312 | – | Q1 and Q2 are strongly hybridised with their resonators (large χ). The notebook also compares R_n 28.1 kΩ (legacy) with the PDK nominal 45 kΩ for Q6. These numbers are the notebook's saved output, not re-run for this page. They are lumped-model estimates (component formulas and calibration), not FEM results; see [the LOM page](../../library/lom.md) for how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, the changes made while rebuilding, and the notes. Source: `components/python/chip_10a_flux_TLQubits.py` (`create_test_chip()`, writes `chip_10a_flux_TLQubits_1.0.oas`), Quantcore internal. Notebook: `examples/designs/legacy/chip_10a_flux_tlqubits.ipynb`. ### Changes made in the rebuild - Junction indexing fixed as on chip_05 (same `bot[i-1]` loop): Q1–Q5 js 5, Q6 js 8. - Flux-line corners: FLUX4 r = 75 µm, FLUX5 r = 100 µm (largest that fit; was 50). Q4 orientation: confirmed. - Junctions: legacy xjc trilayer cells at the legacy fingers on the PDK junction rule (Nb trilayer, Δ = 1.4 meV, I_c·R_n = πΔ/2e = 2.20 mV, R_n 40–50 kΩ, qubits 4–8 GHz; PDK process `get_pdk().junction`: R_n·A 13.5 kΩ·µm², C_J 50 fF/µm², both assumed by the PDK). LOM: Q1/R1 and Q2/R2 hybridised. `claw_tail_gap` = 6 µm (legacy `cap_spacing`). - The notebook's JSON was rebuilt from its layout cell. The notebook has not been re-run, so its outputs are cleared and its PNGs may be out of date. What it is: a revision of chip_05 (`docs/designs/legacy/chip_05_flux_tlqubits.md`): the same layout idea (feedline between two pads, eight `Coupled Resonator`s alternating above/below, seven `Xmon Cross`es whose claws take the resonator tails, Q4/Q5 as SQUIDs with flux lines from two small pads at the top/bottom edge centres, flux-trap holes, junction test pads, labels) with new junction scripts (`xjc_junction_TL_mod` / `xjc_squid_TL_mod`: the trilayer cells the `TrilayerJunction` / `TrilayerSquid` golden tests use), new test pads (eight `xtp_testpads_TL_small`), `Connector Pad 2` feed pads, a 4/6 µm flux line with a 1 µm tip, finer flux holes, and resonator couplers at three strip widths. Everything below is the delta to the chip_05 spec; what is not listed is as chip_05. Die: 7.5 × 7.5 mm, centred on (0, 0) → (+3750, +3750); PDK v2 die frame instead of the legacy `Marker` corners and 10/0 boundary. HSQ corner markers (500/0, `fab_l` 150/0, thickness 50, width 150) at the four corners, as chip_05 → `CornerMarker(hsq=True)`. Pads at all four edge centres again → the automatic device ID slides along the bottom edge to a free spot (`CHIP10A`). Built (`examples/designs/legacy/chip_10a_flux_tlqubits.ipynb`, derived from the chip_05 notebook). Etch XOR 0 on every instance, junction windows included (Q1–Q6 were 600 µm² each with the windows off; on now, and the FEM export drops the window), except the flux-line corners (r = 50 vs 100 µm); junction-layer XOR 0 except Q4 (the legacy SQUID there is upside down, see the notebook). Flux tip: Xmon defaults (flux_x −10.5, tip 0.5, slot 28 × 5) + a 1 µm-wide last route section (`waypoint(a=1, b=7.5, taper_length=1)`); Q2/Q6 `mirror_squid` = the legacy flag. ### Components (legacy frame, µm), delta to chip_05 | instance | legacy → catalog ref | params | at | rot / mirror | |---|---|---|---|---| | FL | Coplanar Waveguide → `CpwSegment` | length 7500 − 2000 − 40 − **210** = 5250, gap 6 (`trace_gap`), lc/rc 2 | (0, 0) | 0 | | PL, PR | **Connector Pad 2** → `BondPad` | 400 × 450, pad_gap 225, taper 450, 10/6, round False, sim False (chip_07's pads) | (∓2625, 0) | 270° / 90° | | PFT, PFB (`cpadT` / `cpadB`) | Connector Pad → `ConnectorPad` | `cpad_tiny`: 400 × 150, taper 100, trace 4, round, sim False | `cpadT` (0, −3155) rot 2 **mirror**; `cpadB` (0, +3155) rot 2 | as chip_05 (names swapped vs position) | | R1 … R8 | Coupled Resonator → `CoupledResonator` | common **gap 6, clength 300, cgap 4, width 304**, neck 400, ground False; cpw_len 4740 / 4920 / 5590 / **6000** / 5200 / 4250 / 5840 / 4500; flip R2, R3, R7, R8; **R8 ground True** (end cap; chip_05's CUT8 box is gone) | x = −2000, −1430, −850, −280, 280, 850, 1430, 2000; y = −(22+2), +(22+4), −(22+4), +(22+2), −(22+4), +(22+4), −(22+6), +(22+6) | mirror True above | | Q1 … Q7 | Xmon Cross → `Xmon` (`_legacy.xmon`) | Q1/Q2/Q4/Q7 `x_cap`: width 400, handle 1, cap_spacing **6**, da **1**, thickness 50, pthickness **35**, fwidth **35**, spacing 20, ggap **6**, hlength **130**; Q6 `x_big`: as x_cap with width 600, hlength 150; **Q3, Q5 `gx`**: pthickness 20, fwidth 50, hlength 150, width 400 (rest as x_cap) | (−1998, −2077), (−1432, 2259), (−852, −2500), (−278, 2492), (282, −2110), (852, 2098), (1428, −2345) | rot 0 / 2 alternating (Q1 0, Q2 2, …) | | junctions | `xjc_junction_TL_mod.create_junction(bot[i−1], 0.6)` / `xjc_squid_TL_mod.create_squid` (Q4, Q5) → `TrilayerJunction` / `TrilayerSquid` (golden-tested on these scripts) | `bot = [5, 5, 5, 5, 5, 8]` × 0.1 µm with the `bot[i−1]` indexing bug kept from chip_05: Q1 **0.8 µm**, Q2–Q6 0.5 µm; second finger 0.6 µm; Q7 none | (x, y ± 200 ± gap/2) with gap 20 → y ± 210; Q6 + 100 | mirror flag: Q1 F, Q2 T, Q3 F, Q4 F, Q5 F, Q6 T (the SQUID branch toggles it twice) | | FLUX4, FLUX5 | raw paths, 4 µm centre / 6 µm gaps, corners rounded at 100 µm, + 1 µm-wide tip + 28 × 5 µm ground box | top: (0, 3155) → (0, 3000) → (−267, 3000) → (−267, 2770), tip to (−267, 2712.5), box centred at (−281.5, 2715); bottom: (0, −3155) → (0, −2795) → (271, −2795) → (271, −2490), tip to (271, −2330.5), box at (285.5, −2333) | as chip_05 (routes `PFT.a → Q4.flux`, `PFB.a → Q5.flux`, a/b 4/6) with the new corners | | | H0 … H7 | hole array → `FluxHoleArray` | **5 µm** holes at **50 µm** pitch, nx = int(400/50) = 8, ny = int(1500/50) = 30 (on 1/0 and 3/0) | first hole at (x − 50, y): x = −2090, −1520, −920, −340, 180, 770, 1350, 2000; y = 65 / −1500 alternating | 0 | | TP1 … TP8 | `xtp_testpads_TL_small.create_testPad(bf/0.2, 0.6)` (`TEST_TL`) → `JunctionTestPads(**legacy_test_pad_params("xtp_testpads_TL_small", bf/0.2, 0.6))` | bf 0.5 (TP1–4), 0.8 (TP5–8) | (−3000, 2000), (−2800, 2000), (−2600, 2000), (−2400, 2000), (3000, −2000), (2800, −2000), (2600, −2000), (2400, −2000) | 0 | | labels | `TextGenerator` mag 200 → `TextLabel` | "500nm" at (−3050, 1580), "800nm" at (2350, −2400), "QCG_Nb11_W" at (1275, −3100) | | 0 | | CLEARER | 30 × (20 + 25) µm boxes cut from 1/0 and 3/0 at every junction (Q1–Q6) | `Xmon(junction_window=[30, 45, 12.5])` (junctions: from the cross end 25 µm into the ground) / `[30, 45, -12.5]` (SQUIDs Q4, Q5); dropped in the FEM export | (x, y ± 200 ± 10 ± 12.5); Q4/Q5 shifted ∓25 ("for squids cut inside"); Q6 + 100 | | ### LOM node structure As chip_05: `FL.line` (50 Ω at each pad) ─ HANGER `K_Ri` ─ `Ri.res` λ/4 (shorted at the coupler) ─ tail joined to `Qi.claw_n` (`wire` coupling) ─ C_g ─ `Qi` island (JJ / SQUID to ground; Q7 none). FLUX4/FLUX5 → `control:flux` of Q4 / Q5. R8 plain (open end cap, no qubit). ### Targets Source comments: R4 "5 GHz, reduced 200 µm for this flux, should shift a bit right"; otherwise as chip_05 (R1 6.5, R2 6.25, R3 5.5, R5 6, R6 7.2, R7 5.25, R8 7 GHz). ### Simplifications for a first rebuild As chip_05 (frame; flux-line tip geometry through the Xmon flux-port parameters; labels as `TextLabel`).