# Hackathon chip (Metal A.6) Two pocket transmons with charge lines, 1.4 mm apart and joined by a short direct coupling line. Each qubit is read out by a λ/2 resonator through a three-finger series capacitor to an edge bond pad. It is the exercise chip of the Qiskit Metal hackathon (South Korea, 2020; Apache-2.0, © IBM and contributors). The Quantcore rebuild is distributed under GPL-3.0. Build this one to learn readout through a series capacitor, a non-resonant coupling line between two qubits, and how charge lines enter a pocket from a pad on the die edge. ```{image} ../../images/designs/metal/a6_hackathon_2q.png :alt: The whole a6 chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/metal/a6_hackathon_2q.ipynb` (an older one-cell version is kept as `a6_hackathon_2q.v1.ipynb`) | | Source | Qiskit Metal `A.6-Hackathon-exercise-South-Korea-2020.ipynb`, © IBM and contributors, Apache-2.0 | | Chip | 9 × 6 mm (the source's size, larger than the 7.5 mm Quantcore die) | | On the chip | 2 pocket transmons with charge lines · 2 series capacitors · 2 λ/2 readouts (5 and 6 mm) · 1 direct coupling line · 2 charge lines · 4 bond pads | | Builds today | yes (layout built on 2026-11-19 in 8 s) | ## How the notebook builds it ```{image} ../../images/designs/metal/a6_hackathon_2q_steps.png :alt: The layout segments of a6, one picture each :width: 100% ``` 1. **Die.** An empty 9 × 6 mm chip with the QCT frame (dicing marks, alignment grids, chip boundary, device ID). 2. **Bond pads.** Readout and charge-line launchpads, slid to the 100 µm pad-edge rule (the picture zooms on one pad). 3. **Capacitors.** The two series capacitors and their lines to the readout pads. 4. **Qubits.** Two Metal pocket transmons with Quantcore junctions; the second is rotated 180°. 5. **Readout resonators.** Two λ/2 lines from the qubits through the capacitors, drawn as U-shapes. 6. **Coupling.** One short direct line between the two qubits' bus pads. 7. **Charge lines.** One line from a south (Q1) and a north (Q2) launchpad into each charge pin. 8. **Whole chip.** Sim groups for the FEM jobs, the content centred in the die, the design saved. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 9 s): QuCat normal modes with QuTiP dressed values. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q1+read | Q1 | 6.96 | -328 | Readout_Q1 | 11.7 | 2.42 | -1.63 | | Q2+read | Q2 | 7.435 | -311 | Readout_Q2 | 9.867 | 1.47 | -3.39 | | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | Q1+Q2+bus | Q1-Q2 | -6870 | yes | no | ```{image} ../../images/designs/metal/a6_hackathon_2q_lom.png :width: 80% :alt: LOM plot of a6_hackathon_2q ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. > The `metal:` references in this spec build as written, through the `metal:` wrapper (ports are the Metal pin names, parameters the Metal options). The Quantcore and KQC substitutions are optional. Source: Quantum Metal `docs/circuit-examples/full-design-flow-examples/A.6-Hackathon-exercise-South-Korea-2020.ipynb`. Licence Apache-2.0. The chip has two `TransmonPocketCL` qubits 1.4 mm apart, joined by a short direct coupling line (non-resonant; the LOM uses bus f = 0.1 GHz). Each qubit has a meander readout through a 3-finger `Cap3Interdigital` series cap to its own edge pad, and a charge line from a top or bottom pad. Chip: DesignPlanar default 9000 × 6000 µm, centred, so **Designer = Metal + (4500, 3000)**. CPW 10/6 µm, fillet 99 µm. The junctions are FakeJunction_01 (Q1) and FakeJunction_02 (Q2). A first build uses these substitutions: `Xmon` for TransmonPocketCL, KQC `FingerCapacitorSquare` for Cap3Interdigital, `BondPad`, free-end charge lines. ### Components Metal TransmonPocketCL options: pad_width 425, pocket_height 650, cl_pocket_edge 180 (cl_off_center 50 default); pads readout (+1, +1) and bus (−1, −1), both default 125 × 30. | instance | catalog ref | key params | at (x, y) | rot | notes | |---|---|---|---|---|---| | Q1 | `Xmon(claws=["n","w"])` (metal:TransmonPocketCL) | see above; hfss Lj 14 nH | (5200, 3000) | 0 | claw_n = readout (Metal pin (5625, 3195) E); claw_w = bus (Metal (4775, 2805) W); Metal CL pin (5617, 2945) E | | Q2 | `Xmon(claws=["n","w"])` | Lj 12 nH | (3800, 3000) | 180 | claw_n→S = readout (Metal (3375, 2805) W); claw_w→E = bus (Metal (4225, 3195) E); Metal CL (3383, 3055) W | | Cap_Q1 | KQC `FingerCapacitorSquare(finger_number=3, finger_length=40)` (metal:Cap3Interdigital) | trace 10 | (7000, 3250) | 0 | Metal a (6935, 3250) W ← resonator, b (7065, 3250) E → pad | | Cap_Q2 | `FingerCapacitorSquare(finger_number=3, finger_length=40)` | | (2000, 2750) | 180 | Metal a (2065, 2750) E ← resonator, b (1935, 2750) W → pad | | Launch_Q1_Read | `BondPad(80, 80, gap 58, taper 122)` | | (7975, 3000) | 90 | east edge | | Launch_Q2_Read | `BondPad` | | (1025, 3000) | 270 | west edge | | Launch_Q1_CL | `BondPad` | | (5850, 525) | 0 | south | | Launch_Q2_CL | `BondPad` | | (3150, 5475) | 180 | north | ### Routes | route | from → to | type, length | waypoints | notes | |---|---|---|---|---| | Bus_Q1_Q2 | Q1.claw_w → Q2.claw_w | cpw ≈ 855–900 | — | direct coupling line; Metal RoutePathfinder via (4475, 2805), (4475, 3195), end lead 250 | | Readout_Q1 | Q1.claw_n → Cap_Q1.a | meander 5000 | — | λ/2 (both ends capacitive); Metal lead 325/125, asym −50 | | Readout_Q2 | Q2.claw_n → Cap_Q2.a | meander 6000 | — | λ/2; same leads | | TL_Q1 | Launch_Q1_Read.a → Cap_Q1.b | cpw ≈ 1075 | nodes [(7215, 3000), (7215, 3250)] | end lead 150 | | TL_Q2 | Launch_Q2_Read.a → Cap_Q2.b | cpw ≈ 1075 | nodes [(1785, 3000), (1785, 2750)] | | | TL_Q1_CL | Launch_Q1_CL.a → `free_end((5617, 2945), dir=0, term=6)` | cpw ≈ 2611 | nodes [(5850, 2945)] | charge line approaches from the east | | TL_Q2_CL | Launch_Q2_CL.a → `free_end((3383, 3055), dir=180, term=6)` | cpw ≈ 2611 | nodes [(3150, 3055)] | from the west | The FingerCapacitorSquare ports are `a`/`b`. Wire them so the resonator lands on the inner port and the pad route on the outer port. ### Launchers, pads, test structures, markers, labels 4 pads: 2 readout (E/W edges) and 2 charge (S, N). There are no markers. ### LOM node structure - Q1 and Q2 are islands with JJs: Q1 Lj 14 nH, Q2 Lj 12 nH. - They are coupled directly through the bus line, which acts as a coupling capacitor network rather than a resonator. - Each qubit has a λ/2 readout with C_g at the claw and a series C (3-finger) to its 50 Ω port. - Each qubit has an open charge line with C_d. ### Targets (if stated) LOM setup (Q1): Lj 14 nH, Cj 2 fF, freq_readout 7.0 GHz, freq_bus [0.1, 0.1] (non-resonant). EPR sweep: Lj1 14 nH, Lj2 12 nH, 2 modes above 3 GHz. A 5 mm λ/2 readout sits near 12 GHz on Si, so lengths do not match the 7 GHz readout assumption. Retune with the LOM loop (about 8.4 mm for 7 GHz on Si, 9.0 mm on sapphire). ### Simplifications for a first rebuild 1. Move the Xmon readout claw to north (Q1) and south (Q2), so the charge lines can approach on the open east/west sides at the Metal CL pin positions. 2. Make the direct bus a straight cpw between facing claws. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/metal/a6_hackathon_2q.ipynb`](../../../examples/designs/metal/a6_hackathon_2q.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), drawn on the source's 9 × 6 mm chip (the design does not fit the 7.5 mm die); no KQC chip frame. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); Metal's `DesignPlanar` default is silicon (εr 11.45, 750 µm), so the LOM capacitances, resonator frequencies and FEM jobs here are for sapphire rather than the source's substrate. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). The source detunes the qubits (`hfss_inductance` 14 / 12 nH); the rebuild keeps that 14 : 12 ratio around the PDK nominal: Q1 L_J 7.32 nH (R_n 48.9 kΩ, C_J 13.8 fF), Q2 6.24 nH (41.7 kΩ, 16.2 fF), both in the 40–50 kΩ window. Expected f_q ≈ 6.9 / 7.4 GHz (estimates). - Kept: the topology and every Metal component with the source's options (through the `metal:` wrapper), positions and orientations, every route's end pins and total length, the sim groups (readouts 5.0 / 6.0 mm, the direct coupling line, the two charge lines).