# IMS 2022 workshop chip (Metal A.7) Three pocket transmons in a triangle, all coupled to each other through three λ/2 buses. Two are read out through interdigital tees on a short north feedline; the third has its own series capacitor and bond pad. It is the chip of the Qiskit Metal IMS 2022 workshop (Apache-2.0, © IBM and contributors), in the state the tutorial reaches after tuning. The Quantcore rebuild is distributed under GPL-3.0. Build this one to see all-to-all coupling of three qubits and the design targets the tutorial states (qubit frequencies near 4.8, 5.0 and 5.2 GHz). It fits inside the standard 7.5 mm Quantcore die. ```{image} ../../images/designs/metal/a7_ims2022_3q.png :alt: The whole a7 chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/metal/a7_ims2022_3q.ipynb` (an older one-cell version is kept as `a7_ims2022_3q.v1.ipynb`) | | Source | Qiskit Metal `A.7-IMS-2022-workshop.ipynb`, © IBM and contributors, Apache-2.0 | | Chip | 7.5 × 7.5 mm Quantcore die (the source's 6 × 6 mm area centred in it), CPW 10 / 6 µm | | On the chip | 3 pocket transmons · 3 λ/2 readouts (8.3 to 8.8 mm) · 3 λ/2 buses (9.35 to 9.7 mm) · 2 interdigital tees · 1 series capacitor · 3 bond pads | | Builds today | yes (layout built on 2026-11-19 in 10 s) | ## How the notebook builds it ```{image} ../../images/designs/metal/a7_ims2022_3q_steps.png :alt: The layout segments of a7, one picture each :width: 100% ``` 1. **Die.** The 7.5 mm die with the QCT frame, and the tutorial's targets attached. 2. **Bond pads.** Three launchpads (two north, one south), slid to the 100 µm pad-edge rule (the picture zooms on one pad). 3. **Feedline.** The north feedline with two interdigital tees, and the third qubit's series capacitor. 4. **Qubits.** Three Metal pocket transmons, their junctions sized for the targets. 5. **Readout resonators.** Three λ/2 serpentines of the tutorial's tuned lengths. 6. **Coupling.** Three λ/2 buses, all-to-all. 7. **Control lines.** None; the qubits are fixed-frequency and driven through their readouts. 8. **Whole chip.** Sim groups for the FEM jobs, the content centred in the die, the design saved. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 15 s): QuCat normal modes with QuTiP dressed values. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q_0+read | Q_0 | 4.844 | -374 | Readout_0 | 6.878 | 0.299 | -1.26 | | Q_1+read | Q_1 | 5.016 | -382 | Readout_1 | 7.109 | 0.33 | -1.31 | | Q_2+read | Q_2 | 5.205 | -418 | Readout_2 | 7.235 | 0.689 | -0.563 | | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | Q_0+Bus_01+Q_1 | Q_0-Q_1 | 22.3 | yes | no | | Q_0+Bus_02+Q_2 | Q_0-Q_2 | 81.2 | yes | no | | Q_1+Bus_12+Q_2 | Q_1-Q_2 | 36.8 | yes | no | ```{image} ../../images/designs/metal/a7_ims2022_3q_lom.png :width: 80% :alt: LOM plot of a7_ims2022_3q ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. > The `metal:` references in this spec build as written, through the `metal:` wrapper (ports are the Metal pin names, parameters the Metal options). The Quantcore and KQC substitutions are optional. Source: Quantum Metal `docs/circuit-examples/full-design-flow-examples/A.7-IMS-2022-workshop.ipynb`. Licence Apache-2.0. The chip has three `TransmonPocket6` qubits in a triangle, all-to-all coupled by three λ/2 bus meanders. The two north qubits are read out through `CapNInterdigitalTee` taps on a short shared feedline; Q_2 reads out through a series `CapNInterdigital` to its own pad. The notebook states full design targets and tunes Q_0, Q_1, Bus_01 and Bus_02 with Q3D-LOM and HFSS-EPR sweeps. Chip 6000 × 6000 µm, centred, so **Designer = Metal + (3000, 3000)**. CPW 10/6 µm, fillet 99 µm. The junctions are FakeJunction_01 cells. The GDS is exported with cheesing (3 µm holes, 50 µm pitch). A first build uses these substitutions: `Xmon` for TransmonPocket6 (3 claws each), hanger `end="open"` (or a KQC splitter plus cap) for the interdigital tee, `FingerCapacitorSquare`, `BondPad`. ### Components TransmonPocket6 base: pad_width 425, pocket_height 650, pad_gap 30 (tuned to 28 on Q_0 and Q_1). | instance | catalog ref | Metal pads (loc_W, loc_H, pad_width, pad_gap) | at (x, y) | rot | claw mapping | |---|---|---|---|---|---| | Q_0 | `Xmon(claws=["n","w","e"])` (metal:TransmonPocket6) | readout (0, +1, 80→100 tuned, 50→22); bus_01 (+1, −1, 60→135, 10); bus_02 (−1, −1, 60→135, 10) | (1750, 3500) | 0 | n = readout (Metal (1750, 3925) N), e = bus_01 ((2175, 3380) E), w = bus_02 ((1325, 3380) W) | | Q_1 | `Xmon(claws=["n","w","e"])` | readout (0, +1, 80→100, 50→20); bus_01 (−1, −1, 60, 10); bus_12 (+1, −1, 60→130, 10) | (4250, 3500) | 0 | n = readout ((4250, 3925)), w = bus_01 ((3825, 3380)), e = bus_12 ((4675, 3380)) | | Q_2 | `Xmon(claws=["n","w","e"])` | readout (0, −1, 80, 50); bus_02 (−1, +1, 60, 10); bus_12 (+1, +1, 60, 10) | (3000, 1650) | 180 | n→S = readout ((3000, 1225)), w→E = bus_12 ((3425, 1770)), e→W = bus_02 ((2575, 1770)) | | Cap_Readout_Q_0 | hanger on FL (metal:CapNInterdigitalTee, defaults: 5 fingers × 20 µm, cap_width 10, cap_gap 6) | | centre (1500, 5250) | — | Metal second_end (1500, 5104) S | | Cap_Readout_Q_1 | hanger on FL | same | centre (4500, 5250) | — | second_end (4500, 5104) S | | Cap_Readout_Q_2 | KQC `FingerCapacitorSquare` (metal:CapNInterdigital, 5 × 20 µm) | | (1000, 677) | 90 | Metal span 604–750; b (N) ← resonator, a (S) → pad | | Launch_Readout_Q_0 | `BondPad(80, 80, gap 58, taper 122)` | | (1000, 5475) | 180 | north edge, feedline in | | Launch_Readout_Q_1 | `BondPad` | | (5000, 5475) | 180 | feedline out | | Launch_Readout_Q_2 | `BondPad` | | (1000, 525) | 0 | south edge | ### Routes | route | from → to | type, length | waypoints / hanger | notes | |---|---|---|---|---| | FL | Launch_Readout_Q_0.a → Launch_Readout_Q_1.a | cpw ≈ 4450 | nodes [(1000, 5250), (5000, 5250)] | Metal TL_Readout_Q_0 + TL_Readout_Q_01 (2900) + TL_Readout_Q_1 | | Readout_0 | Q_0.claw_n → `FL.hanger(s=725, length=100, side="right", ground_gap=3, end="open")` | meander 8900 | — | λ/2; Metal 8.8 mm, lead 125/25, start jog L350, asym 50 | | Readout_1 | Q_1.claw_n → `FL.hanger(s=3725, length=100, side="right", ground_gap=3, end="open")` | meander 8600 | — | λ/2; Metal 8.5 mm, jog R350 | | Readout_2 | Q_2.claw_n → Cap_Readout_Q_2.b | meander 8300 | — | λ/2; asym 200 | | TL_Readout_Q_2 | Cap_Readout_Q_2.a → Launch_Readout_Q_2.a | cpw ≈ 80–190 | — | | | Bus_01 | Q_0.claw_e → Q_1.claw_w | meander 10 300 → tuned 9550 | — | target 5.8 GHz; lead 125/125, asym −350 | | Bus_02 | Q_0.claw_w → Q_2.claw_e | meander 10 000 → tuned 9350 | — | target 6.0 GHz; start jogs L350, L500; lead 125/225 | | Bus_12 | Q_1.claw_e → Q_2.claw_w | meander 9700 | — | target 6.2 GHz; start jogs R350, R700; lead 325/25 | For the hangers, `s` is the arclength from Launch_Readout_Q_0.a (225 µm down, then east). The tee leg is centred, so `direction` does not matter for an open end. ### Launchers, pads, test structures, markers, labels 3 pads: the feedline in/out at the north (x 1000 and 5000) and the Q_2 readout at the south. There are no markers. Fabrication GDS uses `cheese` on layer 1 with a no-cheese buffer of 40 µm. ### LOM node structure - Q_0, Q_1 and Q_2 are islands with JJs, all-to-all coupled through λ/2 buses (C_g at each claw). - R0 and R1 are λ/2 resonators, C_g at the claw and C_κ (tee) to FL, which runs between two 50 Ω ports. - R2 is λ/2, with C_g at the claw and a series C to its 50 Ω port. - There are no control lines. ### Targets (if stated) | quantity | Q_0 | Q_1 | Q_2 | |---|---|---|---| | f_q (GHz) | 4.8 | 5.0 | 5.2 | | readout f (GHz) | 6.8 | 7.0 | 7.2 | | tuned Lj (nH), Cj 2 fF in LOM | 14.9 | 13.9 | 14 (untuned) | The common targets are anharmonicity 300 MHz, qubit–bus g 80 MHz, qubit–readout χ 1 MHz, readout Q_ext 2000 and bus frequencies 5.8 / 6.0 / 6.2 GHz (Bus_01, Bus_02, Bus_12). The Bus_02 sweep tried 9.4, 9.3 and 9.2 mm and gave 9.35 mm. ### Simplifications for a first rebuild 1. Use Xmon claws for the TransmonPocket6 pads, and use the LOM loop (`d.targets(...)`) to retune the claw sizes and Lj toward the table instead of copying the pocket pad sizes. 2. The interdigital tee is a hanger `end="open"`. For fidelity, put a KQC `WaveguideCoplanarSplitter` (ports a/b/c) in FL and a `FingerCapacitorSquare` on port c. 3. Keep the tuned bus lengths (9550 / 9350 / 9700) as the starting point. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/metal/a7_ims2022_3q.ipynb`](../../../examples/designs/metal/a7_ims2022_3q.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 6 × 6 mm chip area is centred in it (`box=(-750, -750, 6750, 6750)`), so every coordinate stays the source's. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); Metal's `DesignPlanar` default is silicon (εr 11.45, 750 µm), so the LOM capacitances, resonator frequencies and FEM jobs here are for sapphire rather than the source's substrate. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). Each qubit is sized for the tutorial's target f_q (4.8 / 5.0 / 5.2 GHz) with its C_Σ (≈ 49–56 fF) from the LOM: straight fingers 0.22 / 0.23 / 0.23 µm × 0.6 µm, L_J 15.3 / 14.6 / 14.6 nH, C_J 6.6–6.9 fF, so R_n ≈ 98–104 kΩ, above the 40–50 kΩ window. These pockets are small (a 45 kΩ junction would put them at ≈ 7.0–7.3 GHz, still inside 4–8 GHz). Cell 1 prints the sizing. - Kept: the topology and every Metal component with the source's options (through the `metal:` wrapper), positions and orientations, every route's end pins and total length, the sim groups (buses 9550 / 9350 / 9700 µm, readouts 8800 / 8500 / 8300 µm, all stated targets).