# iSWAP 1: concentric transmons Two mm-scale concentric transmons (a disk inside a SQUID ring) coupled directly by a straight 4.6 mm line, each wired to a lumped meander resonator, with a separate drive line. It is example 1 of the Qiskit Metal iSWAP-gate notebook (after Phys. Rev. Applied 10, 034050; Apache-2.0, © IBM and contributors). The notebook says the aim is to show the structure of each device, and that the exact geometry is secondary. The Quantcore rebuild is distributed under GPL-3.0. Build this one to learn how large metal-frame components (lumped resonators, concentric qubits) sit in pockets, and how lines inside a pocket are drawn as metal strips with a wire. ```{image} ../../images/designs/metal/iswap1_concentric_direct.png :alt: The whole iswap1 chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/metal/iswap1_concentric_direct.ipynb` (an older one-cell version is kept as `iswap1_concentric_direct.v1.ipynb`) | | Source | Qiskit Metal `Full-Physical-Design-of-iSWAP-Gates.ipynb`, example 1, © IBM and contributors, Apache-2.0 | | Chip | 32 × 25 mm (the pockets overhang the source's 32 × 20 mm chip) | | On the chip | 2 concentric transmons with Quantcore SQUIDs · 2 lumped resonators (5 × 5 mm frame) · 1 direct 4.6 mm coupling line · 1 drive line · 3 bond pads | | Builds today | yes (layout built on 2026-11-19 in 12 s) | ## How the notebook builds it ```{image} ../../images/designs/metal/iswap1_concentric_direct_steps.png :alt: The layout segments of iswap1, one picture each :width: 100% ``` 1. **Die.** An empty 32 × 25 mm chip with the QCT frame (dicing marks, alignment grids, chip boundary, device ID). 2. **Bond pads.** Three launchpads slid to the 100 µm pad-edge rule (the picture zooms on one pad). 3. **Resonators.** Two lumped resonators with their pockets and lines to the pads. 4. **Qubits.** Two concentric transmons with Quantcore SQUIDs, at -45° and 135°, with their pockets. 5. **Qubit lines.** The lines from the qubits' `pin3` fingers to the resonators. 6. **Coupling.** The straight 4.6 mm line between the two qubits. 7. **Drive line.** An open-ended line that ends 500 µm below qubit 1's ring (the picture zooms on it). 8. **Whole chip.** The sim group for the qubits, the centring check, the design saved. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 10 s): QuCat normal modes with QuTiP dressed values. | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | qubit1+route1+qubit2 | qubit1-qubit2 | – | yes | yes | ```{image} ../../images/designs/metal/iswap1_concentric_direct_lom.png :width: 80% :alt: LOM plot of iswap1_concentric_direct ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. > The `metal:` references in this spec build as written, through the `metal:` wrapper (ports are the Metal pin names, parameters the Metal options). The Quantcore and KQC substitutions are optional. > The notebook `examples/designs/metal/iswap1_concentric_direct.ipynb` builds all `metal:` cells at the source's scale. Pockets Metal never draws are added as `metal:Rectangle subtract` (qubits 10 × 10 mm, resonators inside the frame plus a slot), in-pocket lines are metal traces plus wires, and the chip is 32 × 25 mm. Source: Quantum Metal `docs/circuit-examples/F.Small-quantum-chips/Full-Physical-Design-of-iSWAP-Gates.ipynb`, Example 1. Licence Apache-2.0. It follows Phys. Rev. Applied 10, 034050 (2018) "only roughly"; the notebook says "the point is the structure of each device, not its exact geometry". Two `TransmonConcentricType2` qubits at 45° are joined directly by a straight CPW. Each qubit drives a lumped (spiral) readout resonator `ResonatorLumped` that goes to a pad. A third pad carries a drive line that ends open near qubit 1. Everything is mm-scale: qubit rad_outer 2 mm, pocket 10 × 10 mm, resonator box 5 × 5 mm, `cpw_width` set to 0.1 mm (gap 6 µm default), pads 0.5 × 1 mm. The chip is 32 × 20 mm, centred at (1, 3) mm, so **Designer = Metal + (15000, 7000)**. Metal layer 1, silicon default. A topology-only rebuild uses these substitutions: KQC `ConcentricTransmon` for TransmonConcentricType2, KQC `SpiralResonatorPolygon` for ResonatorLumped, `BondPad`. ### Components | instance | catalog ref | key params (Metal) | at (x, y) | rot | notes | |---|---|---|---|---|---| | qubit1 | `ConcentricTransmon` (metal:TransmonConcentricType2) | rad_outer 2 mm, rad_inner 1 mm, gap 0.5 mm, jj_w 0.2 mm, pocket 10 mm, fingers 0.1 × 0.5 mm, N finger 2 mm | (15000, 7000) | Metal −45 | Metal pins (Designer frame): pin1 (17700, 7000) E, pin2 (15000, 9700) N, pin3 (12300, 7000) W | | qubit2 | `ConcentricTransmon` | same | (15000, 17000) | Metal 135 | pin1 (12300, 17000) W, pin2 (15000, 14300) S, pin3 (17700, 17000) E | | resonator1 | `SpiralResonatorPolygon` (metal:ResonatorLumped) | box 5 × 5 mm, res_width 10 µm, 14 turns, turn_radius 0.1 mm, inner/outer space 0.19/0.1 mm | (25000, 17000) | Metal −45 | pins used: pin_sw (21464.5, 17000) W, pin_east (26767.8, 15232.2) at −45° | | resonator2 | `SpiralResonatorPolygon` | same | (5000, 7000) | Metal 45 | pins used: pin_se (8535.5, 7000) E, pin_west (3232.2, 5232.2) at −135° | | P1_C, P2_C, P3_C | `BondPad(pad_width=500, pad_height=1000)` | lead_length 0 | (15000, 2000), (2000, 2000), (30000, 14000) | 0, 0, 90 | P3 faces W | | open1i | free end (metal:OpenToGround) | width 100 (cpw_width var), gap 6 | (15000, 4500) | — | drive line end, 2.5 mm below qubit1 | ### Routes | route | from → to | type, length | waypoints | notes | |---|---|---|---|---| | route1 | qubit1.pin2 → qubit2.pin2 | cpw 4600 | — | direct qubit–qubit coupling line (straight, N–S) | | route2 | resonator1.pin_sw → qubit2.pin3 | cpw 3764 | — | readout coupling | | route3 | resonator2.pin_se → qubit1.pin3 | cpw 3764 | — | | | route4 | resonator1.pin_east → P3_C.a | cpw 3580 | [(27475, 14525), (29950, 14000)] | start lead 1 mm | | route5 | resonator2.pin_west → P2_C.a | cpw 3580 | [(2525, 4525), (2000, 2050)] | start lead 1 mm | | route6 | P1_C.a → `free_end((15000, 4500), dir=-90, term=6)` | cpw 2500 | — | drive line to qubit1 | All Metal routes are `RouteStraight` with zero leads unless stated. Trace 100 µm; Metal's gap stays 6 µm. ### Launchers, pads, test structures, markers, labels 3 pads: P1 (drive), P2 (resonator2 out), P3 (resonator1 out). There are no markers. ### LOM node structure - qubit1 (fixed) and qubit2 (flux-tunable in the paper; no flux line is drawn) are each a concentric island pair with a JJ. - A direct coupling network (route1) joins the two pin2 couplers: C_g1–line–C_g2. - Each qubit couples (pin3) to a lumped LC resonator, which is galvanically connected to a 50 Ω port. - P1 is an open drive line (C_d to qubit1). ### Targets (if stated) None (no LOM or simulation for this example). ### Simplifications for a first rebuild 1. Rebuild at µm scale (divide all sizes and positions by about 10; chip 3.2 × 2 mm) with the KQC defaults for ConcentricTransmon (coupler_1/2/3, drive ports) and SpiralResonatorPolygon (ports a, b). Use it only as a reference for anything quantitative. 2. Map the pins: qubit pin2 → `coupler_2`, pin3 → `coupler_3`, drive → `drive`. Resonator in/out → a/b. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/metal/iswap1_concentric_direct.ipynb`](../../../examples/designs/metal/iswap1_concentric_direct.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), drawn on the source's 32 × 25 mm chip (the design does not fit the 7.5 mm die); no KQC chip frame. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); Metal's `DesignPlanar` default is silicon (εr 11.45, 750 µm), so the LOM capacitances, resonator frequencies and FEM jobs here are for sapphire rather than the source's substrate. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed); both qubits get a Quantcore SQUID (the source's are SQUIDs) sized for 4.0 GHz, the bottom of the PDK band: the mm-scale islands (C_Σ ≈ 0.8 pF) would sit at ≈ 2.1 GHz with the nominal SQUID. Straight fingers 0.91 µm × 0.6 µm per junction, L_J 1.85 nH in parallel, C_J 55 fF, so R_n ≈ 12 kΩ, far below the 40–50 kΩ window. This geometry is incompatible with the PDK window at 4–8 GHz (flagged). The two qubits stay identical. - Kept: the topology and every Metal component with the source's options (through the `metal:` wrapper), positions and orientations, every route's end pins and total length, the sim groups (including the pockets Metal never draws, which the rebuild adds).