# Flipmon test chip (QPDK) A QPDK test chip with four flipmons: circular flip-chip transmons whose inner disc and outer ring are on the bottom chip, with a disc on the top chip joined by an indium bump. Each flipmon has its own λ/2 readout on a U-shaped probeline. The layout comes from QPDK's `flipmon_test_chip.pic.yml` (MIT, after Li et al. 2021) and is rebuilt on the Quantcore PDK; the rebuild is GPL-3.0. This notebook shows how a two-chip (flip-chip) cell sits in a design: the bottom chip gets the Quantcore frame, the top chip none. ```{image} ../../images/designs/qpdk/flipmon_test_chip.png :alt: The whole flipmon_test_chip chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/qpdk/flipmon_test_chip.ipynb` (an older one-cell version is kept as `flipmon_test_chip.v1.ipynb`) | | Source | gdsfactory `quantum-rf-pdk` `qpdk/samples/flipmon_test_chip.pic.yml`, MIT (© 2024 gdsfactory) | | Chip | 7.5 × 7.5 mm Quantcore die, the source's 4250 × 6200 µm circuit centred in it, CPW 10 / 6 µm | | On the chip | 4 launchers · 4 flipmons · 4 λ/2 readouts · 1 probeline with 2 series IDCs · 2 flux lines | | Builds today | yes (layout built on 2026-11-19 in 7 s) | ## How the notebook builds it ```{image} ../../images/designs/qpdk/flipmon_test_chip_steps.png :alt: The layout segments of flipmon_test_chip, one picture each :width: 100% ``` 1. **Die.** The Quantcore die with the frame and the device ID. 2. **Bond pads.** Four launchers, slid to the 100 µm pad-edge rule. 3. **Probeline.** The two series IDCs and the U-shaped probeline. 4. **Qubits.** Four flipmons, two facing south and two (mirrored) facing north. 5. **Readouts.** Four λ/2 readouts from the flipmon plates to coupled sections on the probeline. 6. **Coupling.** None. 7. **Flux lines.** Two lines from the top and bottom launchers to open ends between the qubit pairs. 8. **Whole chip.** Sim groups (one per qubit), the content centred in the die, the design saved. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 8 s): QuCat normal modes with QuTiP dressed values. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | Q1R1 | Q1 | 5.385 | -170 | R1 | 12.35 | 0.748 | -0.0434 | | Q2R2 | Q2 | 5.385 | -170 | R2 | 12.85 | 0.841 | -0.0425 | | Q3R3 | Q3 | 5.385 | -170 | R3 | 13.4 | 0.95 | -0.042 | | Q4R4 | Q4 | 5.385 | -170 | R4 | 13.99 | 1.08 | -0.0429 | ```{image} ../../images/designs/qpdk/flipmon_test_chip_lom.png :width: 80% :alt: LOM plot of flipmon_test_chip ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source: [qpdk/samples/flipmon_test_chip.pic.yml](https://github.com/gdsfactory/quantum-rf-pdk/blob/main/qpdk/samples/flipmon_test_chip.pic.yml) (+ `flipmon_test_chip.py` loader; `filled_flipmon_test_chip` in `filled_test_chip.py`) · licence MIT (verified) · Read on 2026-11-02. Reference: Li et al. 2021, vacuum-gap transmon qubits (cited as `liVacuumgapTransmonQubits2021`). What it is: the qubit test chip netlist line for line. The only changes are the qubit cell (`flipmon_with_resonator_and_probeline`) and the resonator lengths; all coupling lengths are the auto default. The flipmon is a circular transmon. Its inner disc and outer ring are on the bottom chip (M1), with a 110 µm-radius disc on the top chip (M2) joined through a 15 µm indium bump. Image: `docs/_static/images/flipmon_test_chip.png` (filled version). Frame: same as [qubit_test_chip](qubit_test_chip.md): **box (0, 0, 4250, 6200)**, **Designer = source + (100, 3100)**. The filled version adds an M2 chip edge and fill on the top chip as well. The first version used the planar KQC `ConcentricTransmon` as a stand-in (geometry only, no LOM model); the rebuild below uses `Flipmon`. ### Components Pads, capacitors and flux lines are identical to [qubit_test_chip](qubit_test_chip.md#components) (PAD_IN, PAD_OUT, PAD_FT, PAD_FB, C_IN, C_OUT). Qubits: | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | Q1 | `MISSING: flipmon` (QPDK `flipmon_with_bbox`) · stand-in `ConcentricTransmon` | inner_circle_radius 60, outer_ring_radius 110, outer_ring_width 60, top_circle_radius 110 (M2), bump_diameter 15, m1_etch_extension_gap 30, m2_etch_extension_gap 40, junction `squid_junction_long` rotated 180° (away from probeline) | (2485, 4725) | coupler faces south | stand-in: r_inner 60, r_outer 110, outer_island_width 60, ground_gap 30 | | Q2 | same | same | (3715, 4725) | south | | | Q3 | same | same | (3715, 1472.6) | north (mirrored) | | | Q4 | same | same | (2485, 1471.6) | north (mirrored) | | Coupler: `plate_capacitor_single(width=10, length=58)` placed 10 µm outside the outer ring (`outer_ring_outside` port), qubit rotated −90°. No Lj is given; assume `junction={"Lj_nH": 12, "Cj_fF": 2}`. ### Routes FL_IN, FL_OUT, FLUX_T and FLUX_B are as in qubit_test_chip. Every coupler uses the QPDK auto length, |−900 − x_coupler| − 100 ≈ **800 µm**, assuming the plate coupler sits under the qubit centre. The U-turn therefore moves east. **FL: C_IN.b (≈930, 3500) → nodes (3815, 3500), (3815, 2700) → C_OUT.b**, with segments [0, 2885] east, [2885, 3685] south and [3685, 6570] west. Hangers use ground_gap 4 µm, side left. `s` is the coupler centre. | route | from → to | type, length | hanger (s, length, side, ground_gap, direction) | coupler x | |---|---|---|---|---| | R1 | Q1 coupler → FL.hanger | meander 5000 | 1055, 800, left, 4, backward | 1585…2385 | | R2 | Q2 coupler → FL.hanger | meander 4800 | 2285, 800, left, 4, backward | 2815…3615 | | R3 | Q3 coupler → FL.hanger | meander 4600 | 4285, 800, left, 4, forward | 3615…2815 | | R4 | Q4 coupler → FL.hanger | meander 4400 | 5515, 800, left, 4, forward | 2385…1585 | ### Launchers, pads, test structures, markers, labels 4 launchers. Filled variant: M1 and M2 chip edges plus fill on both faces (M2 fill 80 µm keep-out around M2 metal). ### LOM node structure - Q_i: one island node (inner disc + top-chip disc through the bump, in parallel) against the outer ring/ground, with a SQUID. The outer ring is the second electrode, so this is a floating two-node model. The plate coupler gives C_g to R_i. - R_i ↔ FL as in qubit_test_chip. FLUX_T / FLUX_B are flux-bias controls. No bus. ### Targets None stated. As λ/4 on Si, 5000 / 4800 / 4600 / 4400 µm give about 6.0 / 6.2 / 6.5 / 6.8 GHz. ### Simplifications for a first rebuild 1. Planar only: `ConcentricTransmon` without the top-chip disc and bump. This is a geometry stand-in. 2. The **flipmon** component: the circular two-face transmon above (M1 disc + ring, M2 disc, bump), with ports `coupler` (outer ring) and `junction`. It needs multi-face support (KQC faces `1t1`/`2b1`). ### First build The first version of `examples/designs/qpdk/flipmon_test_chip.ipynb` used KQC `ConcentricTransmon` (r_inner 60, ring 110–170, gap 30, one 18° arc coupler at r 185) as a planar stand-in; top-chip disc and bump not drawn. Readouts λ/2 (open hangers), as in qubit_test_chip. Lj 12 nH assumed. ### Rebuild with `Flipmon` The ConcentricTransmon stand-in is replaced by **`Flipmon`** (QPDK defaults, `junction_position_rotation=180`; rot 270 for Q1/Q2 = QPDK `qubit_rotation=-90`, rot 90 for the mirrored Q3/Q4). The QPDK ring is 80–140 µm (ring radius 110 = centre), not 110–170 µm as listed above. Readouts start at the `coupler` port, 13 µm beyond QPDK's plate `o1`, so route = `resonator_length` − 13 µm (4987 / 4787 / 4587 / 4387 µm). LOM (lom `Flipmon` model, top disc across an assumed 8 µm flip-chip gap, rough; Lj 12 nH assumed): f_q 4.21 GHz, α −197 MHz (was 5.92 GHz / −431 MHz with the planar stand-in), λ/2 12.55–14.22 GHz, χ −0.03 MHz. Open issue: the Q3D export merges disc and ring into one net (the junction port finds no edge) and has no 2b1 face. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild, not a replica: the netlist, LOM and imported components are kept, the process is Quantcore's. Notebook: [`examples/designs/qpdk/flipmon_test_chip.ipynb`](../../../examples/designs/qpdk/flipmon_test_chip.ipynb). - **Chip:** the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 4.25 × 6.2 mm chip area is centred in it (`box=QP.die_box(4250, 6200)`), so every coordinate stays the source's; the top chip (face 2b1) gets no frame (PDK v3 defines none for the flip-chip top chip). - **Stack:** sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); QPDK's process is Al on Si (εr 11.45), so frequencies are not the QPDK ones. - **Junctions:** Quantcore trilayer SQUIDs on the PDK rule: two 0.25 × 0.6 µm junctions → R_n 45 kΩ in parallel, L_J 6.73 nH at zero flux, C_J 15 fF; fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient (Nb Δ = 1.4 meV, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed), radially across the disc–ring gap (`Flipmon` `junction_params`), in place of the assumed 12 nH + 2 fF. Expected f_q ≈ 5.4 GHz (an estimate; the 12 nH stand-in gave 4.21 GHz). - **Kept:** the topology and every component with the source's parameters and positions, the readout / resonator lengths and coupled sections, the sim groups (readouts 5000 / 4800 / 4600 / 4400 µm, the 800 µm coupled sections, the assumed 8 µm flip-chip gap).