# Gatemon test chip (QPDK) Two carbon-nanotube gatemons, each coupled to its own λ/2 resonator that is measured in transmission, plus a gate line per gatemon. The layout comes from QPDK's `gatemon_test_chip.pic.yml` (MIT; after Riechert et al., Nat. Commun. 2025) and is rebuilt on the Quantcore PDK; the rebuild is GPL-3.0. This notebook is an example of a resonator measured in transmission (IDC, coupler, meander, IDC), of the Quantcore `Gatemon` cell, and of a chip bigger than the standard die. ```{image} ../../images/designs/qpdk/gatemon_test_chip.png :alt: The whole gatemon_test_chip chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/qpdk/gatemon_test_chip.ipynb` (an older one-cell version is kept as `gatemon_test_chip.v1.ipynb`) | | Source | gdsfactory `quantum-rf-pdk` `qpdk/samples/gatemon_test_chip.pic.yml`, MIT (© 2024 gdsfactory) | | Chip | 10 × 10 mm (the source's size, larger than the 7.5 mm die), CPW 10 / 6 µm | | On the chip | 6 launchers · 2 gatemons · 2 gatemon couplers · 2 λ/2 resonators (11946 µm) · 4 series IDCs · 2 gate lines | | Builds today | yes (layout built on 2026-11-19 in 5 s) | ## How the notebook builds it ```{image} ../../images/designs/qpdk/gatemon_test_chip_steps.png :alt: The layout segments of gatemon_test_chip, one picture each :width: 100% ``` 1. **Die.** The 10 × 10 mm chip with the frame and the device ID. 2. **Bond pads.** Six launchers. 3. **IDCs and couplers.** Per channel the input and output IDCs, the gatemon coupler and the leads. 4. **Gatemons.** Two `Gatemon` cells at the coupler. 5. **Resonators.** The rest of each λ/2, from the coupler to the output IDC. 6. **Coupling.** The declared gatemon-to-resonator connection (the channels do not couple to each other). 7. **Gate lines.** One gate CPW per gatemon to its own launcher. 8. **Whole chip.** Sim groups, targets from the source, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 6 s): QuCat normal modes with QuTiP dressed values. | group | qubit | f_q (GHz) | α (MHz) | resonator | f_r (GHz) | κ (MHz) | χ (MHz) | |---|---|---|---|---|---|---|---| | CH_A | G_A | 4.328 | -421 | – | – | – | – | | CH_B | G_B | 4.328 | -421 | – | – | – | – | ```{image} ../../images/designs/qpdk/gatemon_test_chip_lom.png :width: 80% :alt: LOM plot of gatemon_test_chip ``` These are lumped-model estimates (component formulas and calibration), not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from, with every component, port, route and length. Source: [qpdk/samples/gatemon_test_chip.pic.yml](https://github.com/gdsfactory/quantum-rf-pdk/blob/main/qpdk/samples/gatemon_test_chip.pic.yml) · cells `qpdk/cells/gatemon.py` (`gatemon`, `gatemon_coupler`) · licence MIT (verified) · Read on 2026-11-02. Reference (in the YAML `info`): Riechert et al., carbon-nanotube gatemon, Nat. Commun. 2025, https://doi.org/10.1038/s41467-025-62283-y. Image: `docs/_static/images/gatemon_test_chip.png` (filled). What it is: two independent channels (a = south, b = north, mirror images). Each channel runs launcher → series IDC → 600 µm coupler straight (the gatemon island couples here, 200 µm from its start) → 9946 µm meander → 1400 µm tail → series IDC → launcher. That is a **half-wave resonator in transmission**, 11946 µm total. Each gatemon also has a gate electrode routed to its own launcher. Frame: source centred on (0, 0); launchers at ±4850. The filled version's chip edge is about 9930 × 9900 µm. Use **box (0, 0, 10000, 10000)**, **Designer = source + (5000, 5000)**. Si, M1 negative. The YAML `info` gives the gatemon layer stack (hBN εr 3.4, CNT, Nb/Au contacts). The first version used a plain `Swissmon` stand-in for the gatemon (below); the rebuild uses the `Gatemon` and `GatemonCoupler` cells. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | PIN_A / PIN_B | `BondPad` | default | (150, 3000) / (150, 7000) | 270 (faces east) | launcher_in_a/b (−4850, ∓2000) | | POUT_A / POUT_B | `BondPad` | default | (9850, 3000) / (9850, 7000) | 90 (faces west) | launcher_out_a/b (4850, ∓2000) rot 180 | | PG_A | `BondPad` | default | (2600, 150) | 0 (faces north) | launcher_gate_a (−2400, −4850) rot 90 | | PG_B | `BondPad` | default | (2600, 9850) | 180 (faces south) | launcher_gate_b (−2400, 4850) rot −90 | | CI_A / CI_B | `FingerCapacitorSquare` | 4 fingers, 20 long, 2 gap, 5 wide | (3000, 3000) / (3000, 7000) | 0 | cap_in_a/b (−2000, ∓2000) | | CO_A / CO_B | `FingerCapacitorSquare` | same | end of tail, ≈ (8320, 2200) / (8320, 7800) | 0 | cap_out_a/b, placed by connection | | G_A | `MISSING: gatemon` (QPDK `gatemon`) | island_size (150, 150), pocket_gap 60, pocket_gap_top 40, electrode_size (60, 60), electrode_spacing 100, junction_length 1 (CNT weak link), hbn_size (80, 80), gate_tip_width 16, gate_tip_gap 5, gate_length 50 | (3218, 2880) | 0 | gatemon_a (−1782, −2120); readout side faces the line (+y) | | G_B | same | same | (3218, 7120) | mirrored (readout faces −y) | gatemon_b (−1782, 2120) mirror | | K_A / K_B | `MISSING: gatemon_coupler` | length 600, coupling_position 200, island_width 150, pocket_gap_top 40, coupling_capacitance 5.4 fF; K_B qubit_side top | connected to CI_x.b | 0 | a passing CPW with a capacitive island port | ### Routes | route | from → to | type, length | waypoints | notes | |---|---|---|---|---| | IN_A / IN_B | PIN_x.a → CI_x.a | cpw | straight y 3000 / 7000 | probeline_input | | RES_A | CI_A.b → CO_A.a | **meander 11946** (600 coupler + 9946.135 meander, 4 meanders + 1400 tail) | coupler straight east from x ≈ 3030, meander south of y 3000 down to y ≈ 2200, tail east along y 2200 | λ/2; source resonator_a, open_start/open_end false (continuous) | | RES_B | CI_B.b → CO_B.a | meander 11946 | mirror: north of y 7000, tail along y 7800 | resonator_b mirror | | OUT_A | CO_A.b → POUT_A.a | cpw | nodes (8300, 2200), (8300, 3000) | probeline_output_a waypoints (3300, −2800), (3300, −2000) | | OUT_B | CO_B.b → POUT_B.a | cpw | nodes (8300, 7800), (8300, 7000) | | | GATE_A | G_A.gate → PG_A.a | cpw | nodes (3278, 1800), (2600, 1800) | gate_line_a waypoints (−1722, −3200), (−2400, −3200) | | GATE_B | G_B.gate → PG_B.a | cpw | nodes (3278, 8200), (2600, 8200) | | The qubit is not on a hanger. G_x sits in a pocket beside the first straight of RES_x. Our route model has no "pad-beside-route" coupling, so RES_x must be split at the coupling point (needs `gatemon_coupler`). ### Launchers, pads, test structures, markers, labels 6 launchers. The filled variant (`filled_gatemon_test_chip`) adds a chip edge and 15 µm vortex fill. ### LOM node structure - G_x: one island node with C_Σ (target E_C/h = 260 MHz, so C_Σ ≈ 75 fF), and a gate-tunable CNT junction to ground (Lj tunable, no SQUID). C_g ≈ 5.4 fF to the resonator's input-end node. - RES_x: λ/2 CPW between two series IDCs (C_in, C_out), ports PIN_x and POUT_x. The qubit couples near the input voltage antinode. - GATE_x: DC gate control on G_x (sets Ej). No flux lines, no bus. Channels a and b are independent. ### Targets (YAML `info`) readout_target 5.056 GHz (device A bare cavity, both channels) · E_C 260 MHz · g 50 MHz · coupling capacitance 5.4 fF. These are calibrated with QPDK analytical CPW and capacitor models (junction open), not FEM. Check: λ/2 at 5.056 GHz on Si (ε_eff 6.2) is 11.9 mm, matching 11946 µm. ### Simplifications for a first rebuild 1. Stand-in qubit: `Swissmon` (one arm toward RES_x) or `DoublePads`, with `junction={"Lj_nH": 20}` (assumed; about 3.9 GHz at E_C 260 MHz). Place it at G_x and model the gate line as a drive line ending near the island (`free_end`). 2. Treat RES_x as a fixed-length cpw route from CI_x.b to CO_x.a (`meander=11946`). The capacitive qubit tap then needs either `gatemon_coupler` or a short stub, a hanger with `end="open"`, from the qubit coupler to RES_x near s ≈ 200. 3. The components **gatemon** (pocketed 150 µm island with CNT weak link, hBN, top gate; ports `readout`, `gate`) and **gatemon_coupler** (600 µm through-CPW with an island-coupling port at 200 µm, C ≈ 5.4 fF) are needed for the real thing. ### First build The first version of `examples/designs/qpdk/gatemon_test_chip.ipynb` used a KQC `Swissmon` 150 µm square island stand-in (Lj 20 nH assumed) beside the plain resonator straight, coupling declared as `couple(C_fF=5.4)` to `CI_x.b` (a coupling that names a route breaks the C-matrix export). CO_x moved to source x 3000 so the output route can turn at x 3300. ### Rebuild with `Gatemon` + `GatemonCoupler` The `Swissmon` stand-in is replaced: `K_x = GatemonCoupler(length 600, qubit_side bottom|top)` snapped `o1` → `CI_x.b` (QPDK connection), `G_A = Gatemon` snapped `readout` → `K_A.qubit`; `G_B` is mirrored in QPDK, and `Designer.add` drops `mirror` with a snap, so it is placed explicitly (mirror, on `K_B.qubit`) with a wire coupling. Gate routes go to `G_x.gate` via the QPDK waypoints. The KQC IDC is 37 µm longer than QPDK's, so coupler, gatemon and the last gate waypoint sit 18.5 µm east of the source. λ/2 = 600 + 11346.1 µm route. LOM: f_q 4.33 GHz, α −421 MHz (target −260; lom's analytic island C 51 fF vs QPDK's 75 fF; was −1014 with the stand-in), Lj 20 nH assumed. **Open issue:** the λ/2 is missing from the LOM (the coupler line and the meander route between the IDCs resolve to a wire). ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild, not a replica: the netlist, LOM and imported components are kept, the process is Quantcore's. Notebook: [`examples/designs/qpdk/gatemon_test_chip.ipynb`](../../../examples/designs/qpdk/gatemon_test_chip.ipynb). - **Chip:** the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), drawn on the source's 10 × 10 mm chip (the design does not fit the 7.5 mm die); no KQC chip frame. - **Stack:** sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); QPDK's process is Al on Si (εr 11.45), so frequencies are not the QPDK ones. - **Junctions:** there is no Josephson tunnel junction to replace. The gatemon's weak link is a gate-tunable carbon nanotube, so no Quantcore trilayer junction applies, and its contacts / CNT / hBN / Al patch / top gate have no PDK v3 fab layer (not drawn, as before). The LOM keeps the assumed fixed Lj = 20 nH, Cj = 2 fF. - **Kept:** the topology and every component with the source's parameters and positions, the readout / resonator lengths and coupled sections, the sim groups (the 11946 µm λ/2 between the IDCs, the 5.4 fF coupling, the YAML targets).