# Two transmons and a bus (SQDMetal) Two floating tapered-inset transmons, each coupled through a semicircular capacitor to a λ/2 bus resonator between them. There is no feedline. It is a bus-coupling study from the SQDMetal examples (Apache-2.0), rebuilt on the Quantcore PDK with the Quantcore re-implementations of `TransmonTaperedInsets` and the smooth capacitor. Build this one to learn a qubit-bus-qubit chain without any pads, and how SQDMetal's component options map to Quantcore cells. ```{image} ../../images/designs/sqdmetal/2_transmons_wres_comp.png :alt: The whole 2_transmons_wres_comp chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/sqdmetal/2_transmons_wres_comp.ipynb` (an older one-cell version is kept as `2_transmons_wres_comp.v1.ipynb`) | | Source | SQDMetal example `2_transmons_wRes_comp.ipynb`, Apache-2.0 | | Chip | 7.5 × 7.5 mm Quantcore die, the source's 5 × 2 mm area in its middle | | On the chip | 2 tapered-inset transmons · 2 smooth semicircle capacitors · 1 λ/2 bus (6.8 GHz target) | | Builds today | yes (layout built on 2026-11-19 in 9 s) | ## How the notebook builds it ```{image} ../../images/designs/sqdmetal/2_transmons_wres_comp_steps.png :alt: The layout segments of 2_transmons_wres_comp, one picture each :width: 100% ``` 1. **Die.** The Quantcore die with the frame and the device ID. 2. **Bond pads.** None on this chip. 3. **Readout line.** None. 4. **Qubits.** Two `TransmonTaperedInsets` with the source's options. 5. **Readouts.** None. 6. **Coupling.** The two capacitors and the λ/2 bus between them. 7. **Control lines.** None. 8. **Whole chip.** Targets (f_q 4.5 GHz, bus 6.8 GHz), one sim group, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 10 s): QuCat normal modes with QuTiP dressed values. | parameter | LOM (QuTiP) | target | |---|---|---| | `Q1.f_q_GHz` | 4.51 | 4.5 | | `Q1.alpha_MHz` | -176 | – | | `BUS.chi_MHz` | -1.24 | – | | `Q2.f_q_GHz` | 4.52 | 4.5 | | `Q2.alpha_MHz` | -5.88 | – | | `BUS.f_GHz` | 6.56 | 6.8 | | `BUS.kappa_MHz` | 0 | – | | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | | Q1-Q2 | – | yes | yes | ```{image} ../../images/designs/sqdmetal/2_transmons_wres_comp_lom.png :width: 80% :alt: LOM plot of 2_transmons_wres_comp ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. Source: [doc-sphinx/source/examples/2_transmons_wRes_comp.ipynb](https://github.com/sqdlab/SQDMetal/blob/main/doc-sphinx/source/examples/2_transmons_wRes_comp.ipynb) · SQDMetal components `TransmonTaperedInsets` (`SQDMetal/Comps/Qubits.py`), `Smooth_Capacitor_Semicircle` (`Comps/Test_capacitor.py`), `ResonatorMeanderPinPin` · licence Apache-2.0 (verified) · read on 2026-11-02. Stored outputs: layout plot, Palace capacitance matrix, derived circuit parameters. What it is: two floating tapered-pad transmons on a 5 × 2 mm chip. Each is capacitively coupled, through a semicircular "smooth" capacitor on its inner top pad corner, to a 8.96 mm λ/2 meander bus between them (6.8 GHz). There is no feedline, and the chip is a bus-coupling study. Frame: chip 5.0 × 2.0 mm centred at (0, 0), substrate 280 µm, silicon (`siliconcryo`). **Box (0, 0, 5000, 2000)**, **Designer = source + (2500, 1000)**. CPW 10/6 µm. `TransmonTaperedInsets` and `Smooth_Capacitor_Semicircle` have no KQC equivalent, so a first build uses stand-ins: `DoublePads` + its own coupler pad. The rebuild sections below use the Quantcore versions. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | Qubit1 | `MISSING: TransmonTaperedInsets` (SQDMetal) · stand-in `DoublePads` | pads 800 × 110 (pad_width × pad_height), pad_gap 100 (island gap = junction length), pocket 1000 × **420** (pocket_height override; default 800), pocket_lower_tighten 0, taper 200 → 40 over 40 µm, inductor 20 × 36, charge-line pin offset (0, −10) | (1250, 1000) | 0 (pads stacked in y) | source (−1.25, 0) mm | | Qubit2 | same | same | (4150, 1000) | 0 | source (1.65, 0) mm | | Capacitor1 | `MISSING: Smooth_Capacitor_Semicircle` | rect_width 160, rect_length 80, semi_radius 60, fillet 5 | on Qubit1 `top_right_pin` | 180 | | | Capacitor2 | same | same | on Qubit2 `top_left_pin` | 0 | | Junctions: target L_J1 = **13.203 nH**, L_J2 = **13.196 nH** (E_J ≈ 12.38 GHz) for 4.5 GHz, so `junction={"Lj_nH": 13.2, "Cj_fF": 0}`. ### Routes | route | from → to | type, length | notes | |---|---|---|---| | Resonator1 | Capacitor1.a → Capacitor2.a | meander **8960** (λ/2 at 6.8 GHz on Si, 10/6 CPW, 200 nm film) | `ResonatorMeanderPinPin`, start_left False. About 12 meander legs ±250 µm about y 1000, spanning x ≈ 1750…3650 (from the plot) | Stand-in: `d.route("BUS", Q1.cplr, Q2.cplr, meander=8960)` with DoublePads rotated so `cplr` faces the bus (Q1 rot 270, Q2 rot 90). The coupler pad then plays the semicircle capacitor. ### Launchers, pads, test structures, markers, labels None. ### LOM node structure Q1, Q2: floating transmons, two islands each (C1/C2-ground ≈ 73.5 / 79.7 fF, Q-island pair C_Q ≈ 78.8 fF), JJ 13.2 nH. Each couples by C_g ≈ 7.1 fF to the bus resonator (λ/2, C_r ≈ 1446 fF to ground, modelled as L_res 745 pH ∥ C_res 735 fF at 6.8 GHz). Direct Q1–Q2 is negligible (E_Cc 0.18 MHz). No feedline or controls. ### Targets (stated / computed) f_q1 = f_q2 = 4.5 GHz · f_res 6.8 GHz · E_C ≈ 225.4 MHz · g1 ≈ 82.7 MHz, g2 ≈ 83.2 MHz (circuit-parameter block). The notebook's second "coupled" block reports g ≈ 302 MHz with an uncoupled resonator at 30.3 GHz, which looks like a unit or setup slip. Use the first block. ### Simplifications for a first rebuild 1. DoublePads (island extents [800, 110], island_island_gap 100, ground_gap [1000, 420], coupler_extent [160, 80]) as the stand-in. The tapered junction region and semicircle capacitor are cosmetic for a first LOM pass. 2. Wanted: `TransmonTaperedInsets` (floating pads with tapered junction leads and corner pins `top_left_pin` / `top_right_pin` / …) and `Smooth_Capacitor_Semicircle` (rectangle + semicircle pad, pin `a`). ### Build with stand-ins The stand-in build uses DoublePads (pads 800 × 110, gap 100, pocket 1000 × 420, 160 × 20 coupler plate 15 µm above the top pad), Q1 (1250, 1000), Q2 (4150, 1000) (source x −1.25 / +1.65 mm), bus 8960 µm leaving both pockets upward, meander (12 turns) between x 1850 and 3550. ### Rebuild with `TransmonTaperedInsets` + `SmoothCapacitorSemicircle` The DoublePads stand-ins are replaced by `TransmonTaperedInsets` (source options; pocket 1000 × 420) and `SmoothCapacitorSemicircle` (160 × 80, r 60, fillet 5 / 20, orientation 180 / 0) snapped on `top_right_pin` / `top_left_pin`. `chrgln_pin_y_offset` +10 (source −10 overlaps the qubit pad; 0 makes the DRC report open/short at the pin on the pocket edge), lead_length 20. Bus = 8960 − 2 × (25 µm SQDMetal pin inset + 20 µm lead) = 8870 µm, KQC meander, 12 turns. LOM (lom analytic: pads 126 fF to gnd, 37 fF pad–pad, capacitor 25 fF): f_q 4.06 / 4.06 GHz hybridised (target 4.5), bus 6.67 GHz (target 6.8 on Si), χ −0.96 MHz (with the stand-ins: 4.59 GHz / 6.86 GHz). Open issue: the Q3D export merges each qubit's two pads (junction port has no edge). ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/sqdmetal/2_transmons_wres_comp.ipynb`](../../../examples/designs/sqdmetal/2_transmons_wres_comp.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 5 × 2 mm chip area is centred in it (`box=(-1250, -2750, 6250, 4750)`), so every coordinate stays the source's. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); the SQDMetal examples are on silicon (280–500 µm), so frequencies differ from the source's. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). Both junctions are sized for the stated f_q 4.5 GHz with each qubit's LOM C_Σ (≈ 107 fF): straight fingers 0.34 µm × 0.6 µm, L_J ≈ 9.9 nH, C_J ≈ 10.2 fF, so R_n ≈ 67 kΩ, above the 40–50 kΩ window (a 45 kΩ junction would put them at ≈ 5.4 GHz). Drawn across the 20 µm taper-tip gap by `TransmonTaperedInsets` (`junction_params`); cell 1 prints the sizing. - Kept: the topology (two floating transmons, a λ/2 bus through two smooth capacitors), the components with the source's options and positions, the bus length, the targets, the sim group.