# Floating transmon (SQDMetal) One floating tapered-inset transmon with a λ/2 readout that ends in a coupled section on a short through line. It is SQDMetal's Palace eigenmode example (Apache-2.0), rebuilt on the Quantcore PDK. The source's open line ends become two small bond pads, because the LOM needs real ports. Build this one to learn a λ/2 readout on a through line and the Quantcore `TransmonTaperedInsets` cell. ```{image} ../../images/designs/sqdmetal/floating_transmon.png :alt: The whole floating_transmon chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/sqdmetal/floating_transmon.ipynb` (an older one-cell version is kept as `floating_transmon.v1.ipynb`) | | Source | SQDMetal example `Palace_Eigenmode_FloatingTransmon.ipynb`, Apache-2.0 | | Chip | 7.5 × 7.5 mm Quantcore die, the source's 4 × 4 mm area in its middle, CPW 10 / 6 µm | | On the chip | 2 bond pads · 1 line · 1 tapered-inset transmon · 1 λ/2 readout (8960 µm) | | Builds today | yes (layout built on 2026-11-19 in 8 s) | ## How the notebook builds it ```{image} ../../images/designs/sqdmetal/floating_transmon_steps.png :alt: The layout segments of floating_transmon, one picture each :width: 100% ``` 1. **Die.** The Quantcore die with the frame and the device ID. 2. **Bond pads.** Two small pads that replace the source's open line ends. 3. **Line.** A straight 10 / 6 µm through line between the pads. 4. **Qubit.** One `TransmonTaperedInsets` with the source's options. 5. **Readout.** The λ/2 meander from the qubit to the coupled section on the line. 6. **Coupling.** None: one qubit. 7. **Control lines.** None. 8. **Whole chip.** Targets (f_q 4.5 GHz, f_r 6.8 GHz), one sim group, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 8 s): QuCat normal modes with QuTiP dressed values. | mode | kind | f (GHz) | κ (MHz) | A (MHz) | participation | |---|---|---|---|---|---| | Q1 | qubit | 4.676 | 0 | 181 | J_Q1 1.00 | | R1 | resonator | 6.907 | 0.00792 | 0 | R1 1.00 | | parameter | LOM (QuTiP) | target | |---|---|---| | `Q1.f_q_GHz` | 4.49 | 4.5 | | `Q1.alpha_MHz` | -201 | – | | `R1.chi_MHz` | -0.411 | – | | `R1.f_GHz` | 6.91 | 6.8 | | `R1.kappa_MHz` | 0.00792 | – | ```{image} ../../images/designs/sqdmetal/floating_transmon_lom.png :width: 80% :alt: LOM plot of floating_transmon ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. > The KQC `DoublePads` stand-in has a LOM model. The Quantcore rebuild uses `TransmonTaperedInsets`. Source: [doc-sphinx/source/examples/Palace_Eigenmode_FloatingTransmon.ipynb](https://github.com/sqdlab/SQDMetal/blob/main/doc-sphinx/source/examples/Palace_Eigenmode_FloatingTransmon.ipynb) · SQDMetal `TransmonTaperedInsets` + Quantum Metal `CoupledLineTee`, `RouteMeander`, `RouteStraight`, `OpenToGround` · licence Apache-2.0 (verified) · read on 2026-11-02. No stored outputs. Exports GDS via `MakeGDS(...).export(positive)`, then runs a Palace capacitance / eigenmode setup (3 modes from 3 GHz). What it is: one floating tapered-pad transmon. Its readout connector pad runs a λ/2 meander to a `CoupledLineTee` with an open termination, hung on a short straight transmission-line segment (both ends `OpenToGround`; the simulation adds 50 Ω ports). Frame: chip 4 × 4 mm centred at (0, 0), substrate 500 µm, silicon (`siliconcryo`). **Box (0, 0, 4000, 4000)**, **Designer = source + (2000, 2000)**. CPW width 10 µm, gap from `CpwParams.get_gap_from_width` for 50 Ω on Si (≈ 6 µm, not printed). `TransmonTaperedInsets` has no KQC equivalent. A `DoublePads` stand-in covers it for a first build. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | Q1 | `MISSING: TransmonTaperedInsets` · stand-in `DoublePads` | defaults: pads 800 × 110, pocket 1000 × 800, taper_height **0** (override), pad_gap **100**, inductor_height **100**. Readout connector pad_gap 100 (pad 200 × 30, cpw_extend 200) | (2500, 3000) | 90 (dipole along +x) | source (0.5, 1.0) mm | | T1 | coupled section (Metal `CoupledLineTee`, reproduced by a hanger) | coupling_length **220**, coupling_space **5** (ground strip), down_length 100, open_termination **True** | centre (1000, 2000) | 180 | source (−1.0, 0) mm | | P_L / P_R | `BondPad` (needed in our tool; the source has open ends with sim ports) | | (≈100, 2000) / (≈3900, 2000) | 270 / 90 | source line spans x −1.8…0 mm. Extend it to pads | Junction: not given; target f_q 4.5 GHz. Assume `junction={"Lj_nH": 14, "Cj_fF": 0}` (E_C ≈ 0.2 GHz, assumed). ### Routes | route | from → to | type, length | hanger | notes | |---|---|---|---|---| | FL | P_L.a → P_R.a | cpw 10/6 | straight y 2000 | source `feedline_main` (−1.8…0 mm) | | R1 | Q1.cplr → FL.hanger | meander **8960 total** (λ/2 at 6.8 GHz incl. CLT and connector wire; the meander alone is 8960 − extras) | s at x 1000 (s = 1000 − x(P_L.a)), length 220, side **left** (resonator above FL), ground_gap 5, **end="open"** | meander spacing 100, fillet 40, leads 125/125, asymmetry 0 | L_halfwave = 8.96 mm (the same calculation is printed as 8.96 mm in [2_transmons_wres_comp](2_transmons_wres_comp.md)). ### Launchers, pads, test structures, markers, labels None in the source. Add pads only for a fab version. ### LOM node structure Q1: floating two-island transmon with JJ. The readout pad couples by C_g to one island and starts R1 (λ/2, open at both ends, 6.8 GHz). R1's far open end couples to FL over 220 µm with a 5 µm ground strip. FL: two 50 Ω ports. ### Targets (stated) f_q 4.5 GHz, f_res 6.8 GHz (λ/2). ### Simplifications for a first rebuild 1. DoublePads stand-in (island extents [800, 110], island_island_gap 100, ground_gap [1000, 800]) with `cplr` toward +y after rotation. 2. Our hanger ends `open`, so R1 is a native route. Check that the λ/2 length (not λ/4) is what the LOM bridge assumes for an open-open route. ### Build with the stand-in The stand-in build uses the DoublePads stand-in (pads 800 × 110, gap 100, pocket 1000 × 800, rot 90, 200 × 30 coupler); line between two 100 µm BondPads at the source open ends; open hanger 220 µm / 5 µm, backward (open at the west end); Lj 14 nH assumed. ### Rebuild with `TransmonTaperedInsets` The DoublePads stand-in is replaced by `TransmonTaperedInsets` with the source options (`connection_pads` readout pad_gap 100, inductor_height 100, pad_gap 100, taper_height 0, rot 90). R1 starts at the cell's `readout` pin (700 µm from the centre, as SQDMetal); the 410 µm connector wire is inside the cell, so the route is 8960 − 410 = 8550 µm. LOM (Lj 14 nH assumed; pads analytic 93 / 106 / 44 fF; connection pad + wire 73 fF to gnd): f_q 4.10 GHz (target 4.5), α −225 MHz, λ/2 7.02 GHz (target 6.8 on Si), χ −0.36 MHz, κ 0.0066 MHz (with the stand-in: 4.46 GHz / 7.01 GHz / χ −0.59). Open issue: the drawn Manhattan junction does not bridge the 100 µm gap (components). ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/sqdmetal/floating_transmon.ipynb`](../../../examples/designs/sqdmetal/floating_transmon.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 4 × 4 mm chip area is centred in it (`box=(-1750, -1750, 5750, 5750)`), so every coordinate stays the source's. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); the SQDMetal examples are on silicon (280–500 µm), so frequencies differ from the source's. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). The junction is sized for the source's target f_q 4.5 GHz with the LOM C_Σ ≈ 98 fF: straight finger 0.31 µm × 0.6 µm, L_J ≈ 10.9 nH, C_J ≈ 9.3 fF, so R_n ≈ 72 kΩ, above the 40–50 kΩ window (a 45 kΩ junction would put it at ≈ 5.6 GHz). It is drawn across the 100 µm pad gap by `TransmonTaperedInsets` (`junction_params`); cell 1 prints the sizing. - Kept: the topology and the components with the source's options and positions, the 8960 µm λ/2 readout, the 220 µm / 5 µm coupled section, the targets, the sim group.