# Two coupled transmons (SQDMetal) Two floating pocket transmons 1 mm apart, joined by a straight CPW between their facing connection pads. There is no resonator, and the coupling is a direct capacitive link. It is SQDMetal's two-transmon eigenmode example (Apache-2.0), rebuilt on the Quantcore PDK with the `metal:TransmonPocket` wrapper. Build this one to learn the smallest two-qubit chip and how a Qiskit Metal component is used through the `metal:` wrapper. ```{image} ../../images/designs/sqdmetal/two_transmon.png :alt: The whole two_transmon chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/sqdmetal/two_transmon.ipynb` (an older one-cell version is kept as `two_transmon.v1.ipynb`) | | Source | SQDMetal example `two_transmon.ipynb`, Apache-2.0 | | Chip | 7.5 × 7.5 mm Quantcore die, the source's 2.2 × 1.8 mm area in its middle, CPW 10 / 6 µm | | On the chip | 2 Metal pocket transmons · 1 straight CPW coupler | | Builds today | yes (layout built on 2026-11-19 in 7 s) | ## How the notebook builds it ```{image} ../../images/designs/sqdmetal/two_transmon_steps.png :alt: The layout segments of two_transmon, one picture each :width: 100% ``` 1. **Die.** The Quantcore die with the frame and the device ID. 2. **Bond pads.** None. 3. **Readout line.** None. 4. **Qubits.** Two `metal:TransmonPocket` cells. 5. **Readouts.** None. 6. **Coupling.** One straight CPW between the two `readout` pins. 7. **Control lines.** None. 8. **Whole chip.** One sim group, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 6 s): QuCat normal modes with QuTiP dressed values. | parameter | LOM (QuTiP) | target | |---|---|---| | `Q1.f_q_GHz` | 7.07 | – | | `Q1.alpha_MHz` | -349 | – | | `Q2.f_q_GHz` | 7.73 | – | | `Q2.alpha_MHz` | -324 | – | | group | pair | ZZ (kHz) | neighbours | hybridised | |---|---|---|---|---| | | Q1-Q2 | -3880 | yes | no | ```{image} ../../images/designs/sqdmetal/two_transmon_lom.png :width: 80% :alt: LOM plot of two_transmon ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. > The `metal:` references in this spec build as written, through the `metal:` wrapper (ports are the Metal pin names, parameters the Metal options). `metal:TransmonPocket` builds this chip. The Quantcore and KQC substitutions are optional. Source: [doc-sphinx/source/examples/two_transmon.ipynb](https://github.com/sqdlab/SQDMetal/blob/main/doc-sphinx/source/examples/two_transmon.ipynb) · licence Apache-2.0 (`LICENSE`, verified) · read on 2026-11-02. The notebook has no stored outputs. Quantum Metal design, SQDMetal Palace eigenmode (2 modes from 5 GHz), silicon. What it is: two floating pocket transmons 1 mm apart. Their facing connection pads are joined by a straight CPW, so the coupling is a direct capacitive link with no resonator. It is a minimal 2-qubit EPR / eigenmode test. Frame: Metal chip 2.2 × 1.8 mm centred at (0.5, 0) mm, substrate 500 µm (size_z −500 µm). **Box (0, 0, 2200, 1800)**, **Designer = source + (600, 900)**. CPW: Metal defaults (cpw_width 10, cpw_gap 6). The chip uses `metal:TransmonPocket`. A geometry-only stand-in is KQC `DoublePads`. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | Q1 | `metal:TransmonPocket` · stand-in `DoublePads` | pad_width 425, pocket_height 650; other Metal defaults: pad_height 90, pad_gap 30, pocket_width 650. Connection pad `readout`: loc_W +1, loc_H +1 (top-right, facing Q2), pad_width 200 | (600, 900) | 0 | source (0, 0) | | Q2 | same | same, `readout` loc_W −1, loc_H +1 (top-left, facing Q1) | (1600, 900) | 0 | source (1000, 0) | Junctions (Palace lumped ports): Q1 L_J 13 nH, Q2 L_J 9 nH, C_J 0, so `junction={"Lj_nH": 13, "Cj_fF": 0}` and `{"Lj_nH": 9, "Cj_fF": 0}`. ### Routes | route | from → to | type, length | notes | |---|---|---|---| | COUPLER | Q1.readout → Q2.readout | cpw straight (`RouteStraight`, hfss_wire_bonds) | ≈ 1000 − 2·(325 + cpw_extend) µm. Galvanically joins the two connector pads | With the DoublePads stand-in, `cplr` sits at the top centre, not at the top corner. Route Q1.cplr → Q2.cplr with nodes above the pockets, or rotate the qubits ±90° so the couplers face each other. ### Launchers, pads, test structures, markers, labels None (eigenmode model only). ### LOM node structure Q1, Q2: floating two-island transmons (two pad nodes each, JJ between them). Each has one connector pad with C to one island. The connector pads plus the CPW form one shared coupler node, giving Q1–Q2 coupling through C_c1 and C_c2 in series via that node. No resonators, feedlines or control lines. ### Targets None stated. The detuning comes from Lj 13 vs 9 nH (eigenmodes searched from 5 GHz). ### Simplifications for a first rebuild 1. `DoublePads` (island extents [425, 90], island_island_gap 30, ground_gap [650, 650]) with rot 90/270 so `cplr` faces the other qubit. The LOM for DoublePads is not implemented yet. ### Build The notebook uses `metal:TransmonPocket` (the Metal cell itself, not the DoublePads stand-in); coupler route r = 20 µm (the two pins are 150 µm apart). ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/sqdmetal/two_transmon.ipynb`](../../../examples/designs/sqdmetal/two_transmon.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 2.2 × 1.8 mm chip area is centred in it (`box=(-2650, -2850, 4850, 4650)`), so every coordinate stays the source's. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); the SQDMetal examples are on silicon (280–500 µm), so frequencies differ from the source's. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). The source detunes the pair with its Palace junctions (13 / 9 nH); the rebuild keeps that order at the two ends of the 40–50 kΩ window: Q1 R_n 50 kΩ (L_J ≈ 7.5 nH, C_J ≈ 13.5 fF), Q2 40 kΩ (≈ 6.0 nH, ≈ 16.8 fF). Expected f_q ≈ 7.0 / 7.8 GHz (estimates). - Kept: the topology (two floating pockets, a straight coupler), the Metal components with the source's options and positions, the sim group.