# Xmon capacitance (SQDMetal) One cross transmon (Xmon) whose readout meander ends in an open end 40 µm below a through line, so it couples along an open-ended section. It is SQDMetal's Palace capacitance example (Apache-2.0), rebuilt on the Quantcore PDK with the `metal:TransmonCross` wrapper. Build this one to learn an open-ended coupled readout and a second, unused claw (the bus claw stays open). ```{image} ../../images/designs/sqdmetal/xmon_cap_sim.png :alt: The whole xmon_cap_sim chip as the v2 notebook builds it :width: 100% ``` ## At a glance | | | |---|---| | Notebook | `examples/designs/sqdmetal/xmon_cap_sim.ipynb` (an older one-cell version is kept as `xmon_cap_sim.v1.ipynb`) | | Source | SQDMetal example `Palace_Capacitance_Xmon_Gmsh.ipynb`, Apache-2.0 | | Chip | 7.5 × 7.5 mm Quantcore die, the source's 4.6 × 2.4 mm area in its middle, CPW 10 / 6 µm | | On the chip | 2 launchpads · 1 transmission line · 1 cross transmon · 1 meander readout with an open end | | Builds today | yes (layout built on 2026-11-19 in 10 s) | ## How the notebook builds it ```{image} ../../images/designs/sqdmetal/xmon_cap_sim_steps.png :alt: The layout segments of xmon_cap_sim, one picture each :width: 100% ``` 1. **Die.** The Quantcore die with the frame and the device ID. 2. **Bond pads.** Two launchpads on the 100 µm pad rule. 3. **Line.** The through line between the pads (2.7 mm longer than the source's). 4. **Qubit.** One `metal:TransmonCross` with the source's connection pads. 5. **Readout.** A meander up to an open hanger end 40 µm below the line. 6. **Coupling.** None: the bus claw stays open. 7. **Control lines.** None. 8. **Whole chip.** One sim group, centring, save. ## LOM estimates Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 9 s): QuCat normal modes with QuTiP dressed values. | mode | kind | f (GHz) | κ (MHz) | A (MHz) | participation | |---|---|---|---|---|---| | Q1 | qubit | 5.977 | 0 | 184 | J_Q1 1.00 | | R1 | resonator | 16.11 | 0.0247 | 0 | R1 1.00 | | parameter | LOM (QuTiP) | target | |---|---|---| | `Q1.f_q_GHz` | 5.79 | – | | `Q1.alpha_MHz` | -199 | – | | `R1.chi_MHz` | -0.137 | – | | `R1.f_GHz` | 16.1 | – | | `R1.kappa_MHz` | 0.0247 | – | ```{image} ../../images/designs/sqdmetal/xmon_cap_sim_lom.png :width: 80% :alt: LOM plot of xmon_cap_sim ``` These are lumped-model estimates from component formulas and calibration, not FEM results. [The LOM page](../../library/lom.md) says how far to trust them. ## Build spec The rest of this page is the detailed spec the notebook was built from: every component, port, route and length. Source: [doc-sphinx/source/examples/Palace_Capacitance_Xmon_Gmsh.ipynb](https://github.com/sqdlab/SQDMetal/blob/main/doc-sphinx/source/examples/Palace_Capacitance_Xmon_Gmsh.ipynb) · licence Apache-2.0 (verified) · read on 2026-11-02. There are no stored outputs. Pure Quantum Metal parts (`TransmonCross`, `RouteMeander`, `RoutePathfinder`, `LaunchpadWirebond`, `OpenToGround`), meshed with Gmsh for a Palace capacitance run on silicon. What it is: one grounded cross transmon with two claws (readout east, bus west). The readout claw runs a 3.7 mm meander to an open end placed 40 µm below a through transmission line. The open-end lead (300 µm `start_straight`) runs parallel to the line, so the coupling is an open-ended coupled section. Two small launch pads. Frame: chip 4.6 × 2.4 mm centred at (0, −1) mm, substrate 280 µm. **Box (0, 0, 4600, 2400)**, **Designer = source + (2300, 2200)**. CPW 10/6 µm. A first build uses `Xmon`, `BondPad` and a hanger with `end="open"`. ### Components | instance | catalog ref | key params (units) | at (x, y) Designer | rot | notes | |---|---|---|---|---|---| | LP1 | `BondPad` (pad 103 × 103, pad_gap 60, lead 30; scale down from defaults) | | (300, 2200) | 270 (faces E) | Metal orientation 360 at (−2, 0) mm | | LP2 | `BondPad` same | | (4300, 2200) | 90 (faces W) | orientation 180 at (2, 0) mm | | Q1 | `Xmon` (≈ Metal `TransmonCross` defaults: cross_length 200 per arm → tip-to-tip 400, cross_width 20, cross_gap 20) | claws ["e", "w"]: `readout` at 0° (east, Metal default claw), `bus_01` at 180° (west, claw_length 95) | (2907.5, 736) | 0 | source (0.6075, −1.464) mm. `fl_options` is passed but `TransmonCross` draws no flux line | Junction: not set in the notebook (capacitance only). For eigenmode use, assume `junction={"Lj_nH": 12, "Cj_fF": 2}`. ### Routes | route | from → to | type, length | hanger / waypoints | notes | |---|---|---|---|---| | TL | LP1.a → LP2.a | cpw 10/6 (`RoutePathfinder`, fillet 90, end lead 100) | straight y 2200 | | | R1 | Q1.claw_e → TL.hanger | meander **3700** (fillet 99.9) | coupler centre x ≈ 1950 (source −350), length **300**, side **right** (below TL travelling +x), ground_gap **18** (centre spacing 40 = 5 + 6 + 18 + 6 + 5), direction forward, **end="open"** | the open is `OpenToGround` otg1 at (2100, 2160), orientation 180. The 300 µm lead runs west from it, then meanders down to the claw | `s` for R1 = 1950 − x(LP1.a). The bus claw (W) is left unconnected in the source. ### Launchers, pads, test structures, markers, labels 2 launch pads. No fill, markers or labels. ### LOM node structure Q1: grounded cross island with Lj (assumed) to ground and two claw nodes (readout, bus) with C_g. R1 is open at both ends (claw at one, open-to-ground at the other), so it is a λ/2-type line of 3.7 mm (≈16 GHz on Si; the source runs capacitance only, not frequency). R1 couples to TL by coupled-line C/κ at its open end. TL: two 50 Ω ports. ### Targets None (capacitance-matrix extraction example). ### Simplifications for a first rebuild 1. Use a `meander` with `end="open"`. If a λ/4 readout is wanted instead, keep the same layout with `end="short"` (≈ 8 GHz on Si) and say so in the design notes. 2. Drop the bus claw if `Xmon` claw lists need ports to be used. Otherwise leave `claw_w` free for a later bus. ### Build The notebook uses `metal:TransmonCross` (Metal: connector_location 0 = west arm, so the readout claw is on the west) and `metal:LaunchpadWirebond`; open hanger 400 µm from its corner (300 µm straight + 99.9 µm fillet), open end at the OpenToGround x. ### Quantcore PDK rebuild The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore's. Notebook: [`examples/designs/sqdmetal/xmon_cap_sim.ipynb`](../../../examples/designs/sqdmetal/xmon_cap_sim.ipynb). - Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source's 4.6 × 2.4 mm chip area is centred in it (`box=(-1450, -2550, 6050, 4950)`), so every coordinate stays the source's. - Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); the SQDMetal examples are on silicon (280–500 µm), so frequencies differ from the source's. - Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (`junction_type` from `layouts.registry.trilayer_junction`): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed); the `TransmonCross` gets the PDK nominal junction, 0.5 × 0.6 µm fingers → R_n = 45 kΩ, L_J = 6.73 nH, C_J = 15 fF (in the 40–50 kΩ window) (the source sets no junction, being a capacitance-only run). Expected f_q ≈ 5.8 GHz (an estimate). - Kept: the topology and the Metal components with the source's options and positions, the 3.7 mm readout with its 300 µm coupled section and 40 µm spacing, the sim group.