# Quick prototype in KLayout At the end you will have a chip with one Xmon qubit (Q1), one readout resonator (R1) on a feedline, and a flux line, drawn in KLayout. You will also have checked it, run the lumped-circuit (LOM) estimate, exported a simulation job and written the fab files. ## Before you start - The Quantcore plugin is installed in KLayout. See [the KLayout plugin](index.md) for the install. ## 1. New design and chip Open **Quantcore > Design > New design...** and save the file, for example as `hand_q1r1.json`. Leave **Square die** ticked and keep the die width at 7500 µm. The empty die builds with its frame and label. ```{figure} ../images/plugin/window_overview.png :width: 90% The **Quantcore** menu, the three toolbar tools and the Quantcore panel. ``` ## 2. Place the qubit In the **Components** tab, click `Xmon`. Set `junction_type` to `Trilayer Squid` and `flux_port` to true, then double-click `Xmon` and click near (2975, 2200). In **Move/Snap**, double-click the qubit and set x 2975 and y 2200. Set the targets f_q 5.1 GHz and α −220 MHz. In the same dialog, set the junction **L_J** to 12 nH. Without it the LOM has no qubit. ```{figure} ../images/plugin/dialog_component.png :width: 80% The component dialog of the Xmon: position, targets and junction. ``` ## 3. Place the pads and feedline Double-click `BondPad` in the **Components** tab and click near (1125, 3750). Turn it with **[** or **]** so that its port arrow points into the chip. Place a second `BondPad` near (6375, 3750), turned the other way. Place a third `BondPad` for the flux line near (2964.5, 750), facing up. In its table set `pad_width` 300, `pad_height` 300, `pad_gap` 150 and `taper_length` 300. With **Connect**, click the port of the west pad, then the port of the east pad. In the route dialog, name the route `FL` and set its type to `cpw`. ```{figure} ../images/plugin/tab_components.png :width: 90% The Components tab. Pick the library and the class, then double-click a cell to place it. ``` ## 4. Add the readout resonator Hanging the resonator is the same as drawing a route. With **Connect**, click the qubit's claw port `Q1.claw_n`, then click **on the feedline** at about x 3125. In the hanger dialog, leave **Merge into FL (T-junction)** unticked. Set the name `R1`, the type `meander`, **Meander length µm** 4200, **Coupler length** 300, **Side** right and **Ground strip** 6. Press OK. In **Route handles**, double-click R1 on a straight part. Set the targets f 7.2 GHz and g 90 MHz. ```{figure} ../images/plugin/dialog_hanger.png :width: 70% The hanger dialog: the readout resonator hangs off the feedline. ``` ## 5. Route the flux line With **Connect**, click the flux pad's port. Hold **Shift** and click at about (2964.5, 1967), straight above the pad. Then click the qubit's flux port `Q1.flux`. In the route dialog, name the route `FLUX`, set its type to `cpw`, **Line width a** 4 and **Line gap b** 6. In **Route handles** you can drag any node to change the line. Double-click a node to set its exact position. ```{figure} ../images/plugin/route_handles.png :width: 90% Route handles: click a node to pick it up and click again to drop it. ``` ## 6. Check the design Press **Ctrl+Shift+D** or click **Check** in the Flow strip. The **DRC** tab lists the errors, the warnings and the PDK design warnings. There should be no errors. Click a line to zoom to its marker. ```{figure} ../images/plugin/window_check.png :width: 100% The DRC tab after Check. This picture is from another scratch design. ``` ## 7. Run the LOM Press **Ctrl+Shift+O** or click **LOM** in the Flow strip, then click **Run LOM** in the LOM tab. For Q1 + R1 the run takes a few seconds. f_q should land near 5.1 GHz and f_r near 7.2 GHz. ```{figure} ../images/plugin/flow_2_lom.png :width: 60% The LOM tab after Run LOM. ``` ## 8. Look at the values Open the panel's **Values** tab and tick **Show values in the layout**. Each qubit and resonator gets its values (LOM, FEM once imported, the consensus and the target) beside it in the layout, coloured green within tolerance, amber up to twice the tolerance and red beyond. Click a row to select and zoom to that instance. The LOM tab's *Open the circuit picture full size* shows the circuit itself. ```{figure} ../images/plugin/instance_values.png :width: 90% Values on the layout for a Q1 + R1 chip after Run LOM (the targets were chosen to show all three colours). ``` ## 9. Simulate, export only Press **Simulate** in the Flow strip. You do not need to select anything: with nothing selected, the dialog offers the first qubit with its readout. Press **Export the job only**. This writes the job folder, with the geometry and the AEDT scripts, and does not solve it. ```{figure} ../images/plugin/dialog_simulate.png :width: 70% The Simulate dialog. **Export the job only** writes the job folder without a solve. ``` ## 10. Export for fab Click **Fab > Export for fab (mask, netlist, design.py, PNG)...** and choose a folder. The export warns first if Check found errors, and it refuses while a route has failed. It writes `_fab.oas`, `circuit.json`, `design.py` and a PNG. ```{figure} ../images/plugin/flow_5_fab.png :width: 60% The panel after Export for fab: the Fab step is done. ``` ## Where next - [Q1 + R1 tutorial](TUTORIAL_q1_r1.md): every step with all values and the reasons for them. - [Place and route](place-and-route.md): placing, snapping, routes, hangers and sim groups. - [The Flow strip](flow-strip.md): Check, LOM, Simulate, Results and Fab from the panel. - [Tutorials](../tutorials/index.md): the Python tutorials.