CircularTransmonSingleIsland

The PCell declaration for a single island circular transmon.

Source: KQC (KQCircuits). Category: qubit. Module: kqcircuits.qubits.circular_transmon_single_island.

See also the catalog.

Pins

Pins of CircularTransmonSingleIsland

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

coupler_1

187.939

-68.404

340

10

6

coupler port (readout / bus); LOM node coupler_1

coupler_2

100

173.205

60

3

32

coupler port (readout / bus); LOM node coupler_2

coupler_3

-173.205

-100

210

4.5

20

coupler port (readout / bus); LOM node coupler_3

drive

200

-346.41

300

10

6

drive / charge line end; control line (drive) in the LOM

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

mirror_squid

false

–

Mirror SQUID by its Y axis

junction_type

"Manhattan"

–

Junction Type

junction_width

0.02

μm

Junction width for code generated element

r_island

120

μm

Qubit island radius

ground_gap

80

μm

Ground plane gap width

squid_angle

120

degrees

Angular position of the Josephson Junction/s, where the positive x-axis is 0

couplers_r

150

μm

Radius of the couplers positioning

couplers_a

[10, 3, 4.5]

[μm]

Width of the coupler waveguide’s center conductors

couplers_b

[6, 32, 20]

[μm]

Width of the coupler waveguide’s gaps

couplers_angle

[340, 60, 210]

[degrees]

Positioning angles of the couplers, where 0deg corresponds to positive x-axis

couplers_width

[10, 20, 30]

[μm]

Radial widths of the arc couplers

couplers_arc_amplitude

[35, 45, 15]

[degrees]

Couplers angular extension

drive_angle

300

degrees

Angle of the drive port, where 0deg corresponds to positive x-axis

loop_area

100

μm^2

Loop area

fluxline_type

"Fluxline Standard"

–

Fluxline Type

drive_distance

400

µm

Distance of the driveline, measured from qubit centre

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X

C

island – gnd

estimate=65.9, unit=fF, estimate_source=analytic: disk r=120 µm in a 80 µm ground gap (bent CPW), estimate_kind=analytic, uncertainty=±25%

J_X

SQUID

island – gnd

Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0

Cg_X_coupler_1

C

island – coupler_1

estimate=7, unit=fF, estimate_source=rough: arc 92 µm facing the island across 25 µm (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_coupler_1

C

coupler_1 – gnd

estimate=11, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50%

Cg_X_coupler_2

C

island – coupler_2

estimate=11, unit=fF, estimate_source=rough: arc 118 µm facing the island across 20 µm (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_coupler_2

C

coupler_2 – gnd

estimate=9, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50%

Cg_X_coupler_3

C

island – coupler_3

estimate=4.3, unit=fF, estimate_source=rough: arc 39 µm facing the island across 15 µm (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_coupler_3

C

coupler_3 – gnd

estimate=5.4, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50%

Nodes: island, coupler_1, coupler_2, coupler_3.

Simulation export notes

  • C10: route gap strip misses the cell’s etch by < 1 nm at an angled / off-grid port (fab build) (status: fixed; fix in route/waveguide.py (joined_nodes, misses_etch); layouts/chips/design_chip.py (DesignChip._join_ends); assembly/plan.py (RoutePlan.joins))

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "CircularTransmonSingleIsland", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.coupler_1")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components CircularTransmonSingleIsland lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.