metal:StarQubit

A single configurable circle with multiple pads.

Source: Metal (Qiskit Metal). Category: qubit. Module: qiskit_metal.qlibrary.qubits.star_qubit.

See also the catalog.

Pins

Pins of metal:StarQubit

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

pin_cpl1

0

-375

270

10

6

LOM node pin_cpl1

pin_cpl2

356.646

-115.881

342

10

6

LOM node pin_cpl2

pin_cpl3

-220.419

303.381

126

10

6

LOM node pin_cpl3

pin_cpl4

-356.646

-115.881

198

10

6

LOM node pin_cpl4

pin_rdout

220.419

303.381

54

10

6

LOM node pin_rdout

squid_a

0

345

none

10

6

junction pins (the LOM’s L_J); LOM node island

squid_b

0

395

none

10

6

junction pins (the LOM’s L_J); grounded in the LOM

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

junction_type

"Metal"

–

Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line

junction_params

"{}"

–

Trilayer junction cell parameters (JSON dict, e.g. lj_nH)

metal_class

"StarQubit"

–

Quantum Metal component

options

"{}"

–

Metal options as JSON (bare numbers on length options are µm)

open_pins

""

–

Pins left open (comma-separated): keep Metal’s etch beyond them, as drawn with no route attached

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X

C

island – gnd

estimate=49, unit=fF, estimate_source=rough: centre island as a disk (star arms neglected), estimate_kind=rough, uncertainty=±50%

J_X

JJ

island – gnd

Lj_nH=10, Cj_fF=0

Cg_X_pin_cpl1

C

island – pin_cpl1

estimate=29, unit=fF, estimate_source=rough: pad sector facing the island (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin_cpl1

C

pin_cpl1 – gnd

estimate=24, unit=fF, estimate_source=rough: pad outer edge (half CPW), estimate_kind=rough, uncertainty=±50%

Cg_X_pin_cpl2

C

island – pin_cpl2

estimate=29, unit=fF, estimate_source=rough: pad sector facing the island (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin_cpl2

C

pin_cpl2 – gnd

estimate=24, unit=fF, estimate_source=rough: pad outer edge (half CPW), estimate_kind=rough, uncertainty=±50%

Cg_X_pin_cpl3

C

island – pin_cpl3

estimate=29, unit=fF, estimate_source=rough: pad sector facing the island (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin_cpl3

C

pin_cpl3 – gnd

estimate=24, unit=fF, estimate_source=rough: pad outer edge (half CPW), estimate_kind=rough, uncertainty=±50%

Cg_X_pin_cpl4

C

island – pin_cpl4

estimate=29, unit=fF, estimate_source=rough: pad sector facing the island (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin_cpl4

C

pin_cpl4 – gnd

estimate=24, unit=fF, estimate_source=rough: pad outer edge (half CPW), estimate_kind=rough, uncertainty=±50%

Cg_X_pin_rdout

C

island – pin_rdout

estimate=35, unit=fF, estimate_source=rough: pad sector facing the island (CPS), estimate_kind=rough, uncertainty=±50%

Cc_X_pin_rdout

C

pin_rdout – gnd

estimate=30, unit=fF, estimate_source=rough: pad outer edge (half CPW), estimate_kind=rough, uncertainty=±50%

Nodes: island, pin_cpl1, pin_cpl2, pin_cpl3, pin_cpl4, pin_rdout.

Simulation export notes

  • C5: Metal-wrapped junction pins off the metal edges (stand-in sheet is wrong) (status: fixed; fix in sim_tools/builder.py (FaceMetal, junction_gap, junction_sheet, sheet_junction_port))

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "metal:StarQubit", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.pin_cpl1")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components metal:StarQubit lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.