IMS 2022 workshop chip (Metal A.7)

Three pocket transmons in a triangle, all coupled to each other through three λ/2 buses. Two are read out through interdigital tees on a short north feedline; the third has its own series capacitor and bond pad. It is the chip of the Qiskit Metal IMS 2022 workshop (Apache-2.0, © IBM and contributors), in the state the tutorial reaches after tuning. The Quantcore rebuild is distributed under GPL-3.0.

Build this one to see all-to-all coupling of three qubits and the design targets the tutorial states (qubit frequencies near 4.8, 5.0 and 5.2 GHz). It fits inside the standard 7.5 mm Quantcore die.

The whole a7 chip as the v2 notebook builds it

At a glance

Notebook

examples/designs/metal/a7_ims2022_3q.ipynb (an older one-cell version is kept as a7_ims2022_3q.v1.ipynb)

Source

Qiskit Metal A.7-IMS-2022-workshop.ipynb, © IBM and contributors, Apache-2.0

Chip

7.5 × 7.5 mm Quantcore die (the source’s 6 × 6 mm area centred in it), CPW 10 / 6 µm

On the chip

3 pocket transmons · 3 λ/2 readouts (8.3 to 8.8 mm) · 3 λ/2 buses (9.35 to 9.7 mm) · 2 interdigital tees · 1 series capacitor · 3 bond pads

Builds today

yes (layout built on 2026-11-19 in 10 s)

How the notebook builds it

The layout segments of a7, one picture each
  1. Die. The 7.5 mm die with the QCT frame, and the tutorial’s targets attached.

  2. Bond pads. Three launchpads (two north, one south), slid to the 100 µm pad-edge rule (the picture zooms on one pad).

  3. Feedline. The north feedline with two interdigital tees, and the third qubit’s series capacitor.

  4. Qubits. Three Metal pocket transmons, their junctions sized for the targets.

  5. Readout resonators. Three λ/2 serpentines of the tutorial’s tuned lengths.

  6. Coupling. Three λ/2 buses, all-to-all.

  7. Control lines. None; the qubits are fixed-frequency and driven through their readouts.

  8. Whole chip. Sim groups for the FEM jobs, the content centred in the die, the design saved.

LOM estimates

Numbers are from a run of this notebook on 2026-11-19 (Setup, Design, Check and the LOM cells, 15 s): QuCat normal modes with QuTiP dressed values.

group

qubit

f_q (GHz)

α (MHz)

resonator

f_r (GHz)

κ (MHz)

χ (MHz)

Q_0+read

Q_0

4.844

-374

Readout_0

6.878

0.299

-1.26

Q_1+read

Q_1

5.016

-382

Readout_1

7.109

0.33

-1.31

Q_2+read

Q_2

5.205

-418

Readout_2

7.235

0.689

-0.563

group

pair

ZZ (kHz)

neighbours

hybridised

Q_0+Bus_01+Q_1

Q_0-Q_1

22.3

yes

no

Q_0+Bus_02+Q_2

Q_0-Q_2

81.2

yes

no

Q_1+Bus_12+Q_2

Q_1-Q_2

36.8

yes

no

LOM plot of a7_ims2022_3q

These are lumped-model estimates from component formulas and calibration, not FEM results. The LOM page says how far to trust them.

Build spec

The rest of this page is the detailed spec the notebook was built from: every component, port, route and length.

The metal: references in this spec build as written, through the metal: wrapper (ports are the Metal pin names, parameters the Metal options). The Quantcore and KQC substitutions are optional.

Source: Quantum Metal docs/circuit-examples/full-design-flow-examples/A.7-IMS-2022-workshop.ipynb. Licence Apache-2.0. The chip has three TransmonPocket6 qubits in a triangle, all-to-all coupled by three λ/2 bus meanders. The two north qubits are read out through CapNInterdigitalTee taps on a short shared feedline; Q_2 reads out through a series CapNInterdigital to its own pad. The notebook states full design targets and tunes Q_0, Q_1, Bus_01 and Bus_02 with Q3D-LOM and HFSS-EPR sweeps. Chip 6000 × 6000 µm, centred, so Designer = Metal + (3000, 3000). CPW 10/6 µm, fillet 99 µm. The junctions are FakeJunction_01 cells. The GDS is exported with cheesing (3 µm holes, 50 µm pitch). A first build uses these substitutions: Xmon for TransmonPocket6 (3 claws each), hanger end="open" (or a KQC splitter plus cap) for the interdigital tee, FingerCapacitorSquare, BondPad.

Components

TransmonPocket6 base: pad_width 425, pocket_height 650, pad_gap 30 (tuned to 28 on Q_0 and Q_1).

instance

catalog ref

Metal pads (loc_W, loc_H, pad_width, pad_gap)

at (x, y)

rot

claw mapping

Q_0

Xmon(claws=["n","w","e"]) (metal:TransmonPocket6)

readout (0, +1, 80→100 tuned, 50→22); bus_01 (+1, −1, 60→135, 10); bus_02 (−1, −1, 60→135, 10)

(1750, 3500)

0

n = readout (Metal (1750, 3925) N), e = bus_01 ((2175, 3380) E), w = bus_02 ((1325, 3380) W)

Q_1

Xmon(claws=["n","w","e"])

readout (0, +1, 80→100, 50→20); bus_01 (−1, −1, 60, 10); bus_12 (+1, −1, 60→130, 10)

(4250, 3500)

0

n = readout ((4250, 3925)), w = bus_01 ((3825, 3380)), e = bus_12 ((4675, 3380))

Q_2

Xmon(claws=["n","w","e"])

readout (0, −1, 80, 50); bus_02 (−1, +1, 60, 10); bus_12 (+1, +1, 60, 10)

(3000, 1650)

180

n→S = readout ((3000, 1225)), w→E = bus_12 ((3425, 1770)), e→W = bus_02 ((2575, 1770))

Cap_Readout_Q_0

hanger on FL (metal:CapNInterdigitalTee, defaults: 5 fingers × 20 µm, cap_width 10, cap_gap 6)

centre (1500, 5250)

—

Metal second_end (1500, 5104) S

Cap_Readout_Q_1

hanger on FL

same

centre (4500, 5250)

—

second_end (4500, 5104) S

Cap_Readout_Q_2

KQC FingerCapacitorSquare (metal:CapNInterdigital, 5 × 20 µm)

(1000, 677)

90

Metal span 604–750; b (N) ← resonator, a (S) → pad

Launch_Readout_Q_0

BondPad(80, 80, gap 58, taper 122)

(1000, 5475)

180

north edge, feedline in

Launch_Readout_Q_1

BondPad

(5000, 5475)

180

feedline out

Launch_Readout_Q_2

BondPad

(1000, 525)

0

south edge

Routes

route

from → to

type, length

waypoints / hanger

notes

FL

Launch_Readout_Q_0.a → Launch_Readout_Q_1.a

cpw ≈ 4450

nodes [(1000, 5250), (5000, 5250)]

Metal TL_Readout_Q_0 + TL_Readout_Q_01 (2900) + TL_Readout_Q_1

Readout_0

Q_0.claw_n → FL.hanger(s=725, length=100, side="right", ground_gap=3, end="open")

meander 8900

—

λ/2; Metal 8.8 mm, lead 125/25, start jog L350, asym 50

Readout_1

Q_1.claw_n → FL.hanger(s=3725, length=100, side="right", ground_gap=3, end="open")

meander 8600

—

λ/2; Metal 8.5 mm, jog R350

Readout_2

Q_2.claw_n → Cap_Readout_Q_2.b

meander 8300

—

λ/2; asym 200

TL_Readout_Q_2

Cap_Readout_Q_2.a → Launch_Readout_Q_2.a

cpw ≈ 80–190

—

Bus_01

Q_0.claw_e → Q_1.claw_w

meander 10 300 → tuned 9550

—

target 5.8 GHz; lead 125/125, asym −350

Bus_02

Q_0.claw_w → Q_2.claw_e

meander 10 000 → tuned 9350

—

target 6.0 GHz; start jogs L350, L500; lead 125/225

Bus_12

Q_1.claw_e → Q_2.claw_w

meander 9700

—

target 6.2 GHz; start jogs R350, R700; lead 325/25

For the hangers, s is the arclength from Launch_Readout_Q_0.a (225 µm down, then east). The tee leg is centred, so direction does not matter for an open end.

Launchers, pads, test structures, markers, labels

3 pads: the feedline in/out at the north (x 1000 and 5000) and the Q_2 readout at the south. There are no markers. Fabrication GDS uses cheese on layer 1 with a no-cheese buffer of 40 µm.

LOM node structure

  • Q_0, Q_1 and Q_2 are islands with JJs, all-to-all coupled through λ/2 buses (C_g at each claw).

  • R0 and R1 are λ/2 resonators, C_g at the claw and C_κ (tee) to FL, which runs between two 50 Ω ports.

  • R2 is λ/2, with C_g at the claw and a series C to its 50 Ω port.

  • There are no control lines.

Targets (if stated)

quantity

Q_0

Q_1

Q_2

f_q (GHz)

4.8

5.0

5.2

readout f (GHz)

6.8

7.0

7.2

tuned Lj (nH), Cj 2 fF in LOM

14.9

13.9

14 (untuned)

The common targets are anharmonicity 300 MHz, qubit–bus g 80 MHz, qubit–readout χ 1 MHz, readout Q_ext 2000 and bus frequencies 5.8 / 6.0 / 6.2 GHz (Bus_01, Bus_02, Bus_12). The Bus_02 sweep tried 9.4, 9.3 and 9.2 mm and gave 9.35 mm.

Simplifications for a first rebuild

  1. Use Xmon claws for the TransmonPocket6 pads, and use the LOM loop (d.targets(...)) to retune the claw sizes and Lj toward the table instead of copying the pocket pad sizes.

  2. The interdigital tee is a hanger end="open". For fidelity, put a KQC WaveguideCoplanarSplitter (ports a/b/c) in FL and a FingerCapacitorSquare on port c.

  3. Keep the tuned bus lengths (9550 / 9350 / 9700) as the starting point.

Quantcore PDK rebuild

The notebook is a Quantcore PDK rebuild of the source, not a replica: the netlist, LOM and imported components are kept, and the process is Quantcore’s.

Notebook: examples/designs/metal/a7_ims2022_3q.ipynb.

  • Chip: the Quantcore die frame (L dicing markers 1000/0, 3 × 3 alignment grids 1001/0, chip boundary 100/0, device ID where an edge is free; any brand text is QCT), on the 7.5 × 7.5 mm Quantcore die; the source’s 6 × 6 mm chip area is centred in it (box=(-750, -750, 6750, 6750)), so every coordinate stays the source’s.

  • Stack: sapphire 650 µm, εr 10.25 (the PDK default stack, used by the LOM estimates and every FEM export); Metal’s DesignPlanar default is silicon (εr 11.45, 750 µm), so the LOM capacitances, resonator frequencies and FEM jobs here are for sapphire rather than the source’s substrate.

  • Junctions: Quantcore Nb/AlOx/Nb trilayer junctions (junction_type from layouts.registry.trilayer_junction): fingers on 2/0 + 4/0, spacer 50/0 with the 51–53/0 gradient, sized on the PDK junction rule (Nb Δ = 1.4 meV, I_c·R_n = πΔ/2e, R_n·A 13.5 kΩ·µm² and C_J 50 fF/µm² assumed). Each qubit is sized for the tutorial’s target f_q (4.8 / 5.0 / 5.2 GHz) with its C_Σ (≈ 49–56 fF) from the LOM: straight fingers 0.22 / 0.23 / 0.23 µm × 0.6 µm, L_J 15.3 / 14.6 / 14.6 nH, C_J 6.6–6.9 fF, so R_n ≈ 98–104 kΩ, above the 40–50 kΩ window. These pockets are small (a 45 kΩ junction would put them at ≈ 7.0–7.3 GHz, still inside 4–8 GHz). Cell 1 prints the sizing.

  • Kept: the topology and every Metal component with the source’s options (through the metal: wrapper), positions and orientations, every route’s end pins and total length, the sim groups (buses 9550 / 9350 / 9700 µm, readouts 8800 / 8500 / 8300 µm, all stated targets).