ConcentricTransmon¶
The PCell declaration for a concentric transmon.
Source: KQC (KQCircuits). Category: qubit. Module: kqcircuits.qubits.concentric_transmon.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
310.099 |
-112.867 |
340 |
10 |
6 |
coupler port (readout / bus); LOM node |
|
165 |
285.788 |
60 |
3 |
32 |
coupler port (readout / bus); LOM node |
|
-285.788 |
-165 |
210 |
4.5 |
20 |
coupler port (readout / bus); LOM node |
|
200 |
-346.41 |
300 |
10 |
6 |
drive / charge line end; control line (drive) in the LOM |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Mirror SQUID by its Y axis |
|
|
– |
Junction Type |
|
|
μm |
Junction width for code generated element |
|
|
μm |
Outer island radial width |
|
|
μm |
Ground plane padding |
|
|
degrees |
Angular position of the Josephson Junction/s, where the positive x-axis |
|
|
[μm] |
Radius of the couplers positioning |
|
|
[μm] |
Width of the coupler waveguide’s center conductors |
|
|
[μm] |
Width of the coupler waveguide’s gaps |
|
|
[degrees] |
Positioning angles of the couplers, where 0deg corresponds to positive x-axis |
|
|
[μm] |
Radial widths of the arc couplers |
|
|
[degrees] |
Couplers angular extension |
|
|
degrees |
Angle of the drive port, where 0deg corresponds to positive x-axis |
|
|
μm^2 |
Loop area |
|
|
– |
Fluxline Type |
|
|
μm |
Internal island radius |
|
|
μm |
External island radius, measured at the outer edge |
|
|
µm |
Distance of the driveline, measured from qubit centre |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island1 – gnd |
estimate=122, unit=fF, estimate_source=analytic: ring outer edge as half CPW, estimate_kind=analytic, uncertainty=±25% |
|
C |
island1 – island2 |
estimate=91, unit=fF, estimate_source=rough: disk–ring facing edges as coplanar strips along the mean circumference, estimate_kind=rough, uncertainty=±50% |
|
C |
island2 – gnd |
estimate=19, unit=fF, estimate_source=rough: disk to ground screened by the ring, estimate_kind=rough, uncertainty=±50% |
|
SQUID |
island1 – island2 |
Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 |
|
C |
island1 – coupler_1 |
estimate=12, unit=fF, estimate_source=rough: arc 177 µm facing the island across 35 µm (CPS), estimate_kind=rough, uncertainty=±50% |
|
C |
coupler_1 – gnd |
estimate=13, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% |
|
C |
island1 – coupler_2 |
estimate=19, unit=fF, estimate_source=rough: arc 228 µm facing the island across 30 µm (CPS), estimate_kind=rough, uncertainty=±50% |
|
C |
coupler_2 – gnd |
estimate=15, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% |
|
C |
island1 – coupler_3 |
estimate=7, unit=fF, estimate_source=rough: arc 76 µm facing the island across 25 µm (CPS), estimate_kind=rough, uncertainty=±50% |
|
C |
coupler_3 – gnd |
estimate=7.2, unit=fF, estimate_source=rough: arc outer edge (half CPW) + port lead, estimate_kind=rough, uncertainty=±50% |
Nodes: island1, island2, coupler_1, coupler_2, coupler_3.
Simulation export notes¶
C10: route gap strip misses the cell’s etch by < 1 nm at an angled / off-grid port (fab build) (status: fixed; fix in route/waveguide.py (joined_nodes, misses_etch); layouts/chips/design_chip.py (DesignChip._join_ends); assembly/plan.py (RoutePlan.joins))
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "ConcentricTransmon", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.coupler_1") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components ConcentricTransmon lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.