SquidTermination¶
CPW lead shorted to ground through a trilayer SQUID, with a shorted pump / flux line (QPDK squid_termination
Source: Quantcore. Category: termination. Module: quantcore_circuits.layouts.others.amplifiers.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
0 |
180 |
10 |
6 |
CPW end; LOM node |
|
49 |
-180 |
270 |
10 |
6 |
control line (flux) in the LOM |
|
16 |
0 |
none |
10 |
6 |
junction pins (the LOM’s L_J) |
|
36 |
0 |
none |
10 |
6 |
junction pins (the LOM’s L_J) |
Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
CPW lead length |
|
|
μm |
Pocket length along the lead (the junction window height) |
|
|
μm |
Pocket width across the lead |
|
|
– |
Junction across the pocket (trilayer cell) |
|
|
– |
Trilayer junction cell parameters (JSON dict) |
|
|
μm |
Pump line length (port to short) |
|
|
μm |
Ground strip between the pocket and the pump line gap |
|
|
– |
Landing head at the lead end in the pocket (length, width), µm |
|
|
Φ0 |
Static flux bias of the SQUID (LOM) |
|
|
– |
Draw the shorted pump / flux line |
|
|
μm |
Pump short beyond the SQUID axis |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
no lumped branches
line |
node |
length (µm) |
a (µm) |
b (µm) |
ends |
|---|---|---|---|---|---|
|
|
15412.596 |
10 |
6 |
short / short |
Nodes: lead.
X: SQUID L_s = 6.734 nH at Φ = 0 Φ0 (drawn Quantcore Squid (PDK junction rule)) → 15397 µm of 10/6 µm CPW at the shorted end (L’ 437 nH/m incl. kinetic); the SQUID’s Kerr / three-wave mixing is not in the lumped circuit (analysis.amplifiers)
Simulation export notes¶
C9: SquidTermination lead shorted to ground in the drawn cell (fab build too) (status: fixed; fix in layouts/others/amplifiers.py (SquidTermination.build))
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "SquidTermination", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components SquidTermination lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).