QcFlipChipConnectorRf¶
KQC’s flip-chip bump transition (FlipChipConnectorRf) with a bump size and named ports a and b.
Source: Quantcore. Category: flip_chip. Module: quantcore_circuits.layouts.others.flip_chip.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-60 |
0 |
180 |
10 |
6 |
CPW end; LOM node |
|
60 |
0 |
0 |
10 |
6 |
CPW end; LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Notes from the catalog: port ‘a’ is on face_ids[0], ‘b’ on face_ids[1] (default 1t1 → 2b1); a route to either is drawn on that port’s face. bump_diameter / ubm_diameter size the signal bump, n_ground_bumps is 4 (KQC’s) or 0. LOM: one conductor through the bump.
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Ground bumps around the transition (4: KQC’s, 0: none) |
|
|
μm |
Distance between In bumps |
|
|
degrees |
Rotation of output port w.r.t. input port |
|
|
μm |
Conductor width at the connector area |
|
|
μm |
Gap width at the connector area |
|
|
– |
Use round connector shape |
|
|
– |
Number of center bumps in series |
|
|
– |
Bump type |
|
|
μm |
Width of center conductor on the other end |
|
|
μm |
Width of gap on the other end |
|
|
μm |
Under-bump metalization diameter |
|
|
μm |
Bump diameter |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
no lumped branches
line |
node |
length (µm) |
a (µm) |
b (µm) |
ends |
|---|---|---|---|---|---|
|
|
120 |
10 |
6 |
short / short |
Nodes: line.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "QcFlipChipConnectorRf", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components QcFlipChipConnectorRf lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status: not listed in kplugin/COMPONENTS_STATUS.md.