Swissmon¶
The PCell declaration for a Swissmon qubit.
Source: KQC (KQCircuits). Category: qubit. Module: kqcircuits.qubits.swissmon.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-219 |
0 |
180 |
10 |
6 |
coupler port (readout / bus); LOM node |
|
0 |
219 |
90 |
10 |
6 |
coupler port (readout / bus); LOM node |
|
219 |
0 |
0 |
10 |
6 |
coupler port (readout / bus); LOM node |
|
-200 |
-200 |
none |
10 |
6 |
drive / charge line end; control line (drive) in the LOM |
|
0 |
-245.333 |
270 |
10 |
6 |
flux line end; control line (flux) in the LOM |
Pins with direction none: drive. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Notes from the catalog: port ‘drive’ has no direction with default parameters (KQC puts no port_drive_corner). Coupler ports ‘cplr0..2’ have a = port_width[i]; the qubit’s own gap around them is wider than b.
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Mirror SQUID by its Y axis |
|
|
– |
Junction Type |
|
|
μm |
Junction width for code generated element |
|
|
– |
Arm length (um, WNES)) |
|
|
– |
Arm metal width (um, WNES) |
|
|
– |
Arm gap width (um, WNES) |
|
|
– |
Coupler width (um, WNE) |
|
|
– |
Coupler lengths (um, WNE) |
|
|
– |
Coupler gap (um, WNE) |
|
|
– |
Port width (um, WNE) |
|
|
μm |
Center island rounding radius |
|
|
μm^2 |
Loop area |
|
|
– |
Fluxline Type |
|
|
– |
Coupler gap to ground (um, WNE) |
|
|
– |
Chargeline offset (um, um) |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island – gnd |
estimate=78.4, unit=fF, estimate_source=analytic: CPW-arm cross (24/12 µm) × 0.874 Xmon Q3D anchor, estimate_kind=analytic, uncertainty=±25% |
|
SQUID |
island – gnd |
Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 |
|
C |
island – cplr0 |
estimate=3.8, unit=fF, estimate_source=rough: Xmon claw calibration at the coupler length (screened coupler), estimate_kind=rough, uncertainty=±50% |
|
C |
cplr0 – gnd |
estimate=69.3, unit=fF, estimate_source=analytic: horseshoe as CPW 24/6 µm × 366 µm, estimate_kind=analytic, uncertainty=±25% |
|
C |
island – cplr1 |
estimate=3.8, unit=fF, estimate_source=rough: Xmon claw calibration at the coupler length (screened coupler), estimate_kind=rough, uncertainty=±50% |
|
C |
cplr1 – gnd |
estimate=69.3, unit=fF, estimate_source=analytic: horseshoe as CPW 24/6 µm × 366 µm, estimate_kind=analytic, uncertainty=±25% |
|
C |
island – cplr2 |
estimate=3.8, unit=fF, estimate_source=rough: Xmon claw calibration at the coupler length (screened coupler), estimate_kind=rough, uncertainty=±50% |
|
C |
cplr2 – gnd |
estimate=69.3, unit=fF, estimate_source=analytic: horseshoe as CPW 24/6 µm × 366 µm, estimate_kind=analytic, uncertainty=±25% |
Nodes: island, cplr0, cplr1, cplr2.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "Swissmon", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.cplr0") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components Swissmon lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.