quantcore_circuits.layouts.junctions.legacy_junctions

Earlier generations of the QWri trilayer junctions and SQUIDs, as KQC junctions (usable as junction_type).

  • TrilayerJunctionHSQ / TrilayerSquidHSQ: the first HSQ generation, legacy junction_creator_HSQ.create_junction / squid_creator_HSQ.create_squid (chips 05, 06, 08 and the 11f JJ placer). Compared with TrilayerJunction (xjc_*_TL_mod) the bent finger sits 0.5 µm lower in an unshifted window, the HSQ boxes are 0.1 µm (not 0.2 µm) longer than the finger and the SQUID’s straight leads keep the 3 µm finger-pad height.

  • SquidV0: the pre-HSQ SQUID of junction_creator_sq.create_junction_squid (and the stand-alone junction_pad.py, whose bent window is 16 µm high instead of 18 µm): straight fingers at their 0.2 µm default width, bent fingers 0.2·js + 0.06 µm wide, bent window shifted up by 1 µm, no HSQ.

Same layers and frame as trilayer: straight finger → SIS_junction (legacy 2/0), bent finger → SIS_junction_2 (4/0), HSQ → qcc hsq (PDK v2 50/0; legacy 500/0), spacer gradient on 51–53/0 (on by default, spacer_gradient_levels()), sizing by lj_nH / KQC junction_width and the optional CLEARER as in trilayer; origin_squid at the ground-side window edge, port_common on the island side; geometry computed with the legacy pya calls, so it XORs clean against them. The legacy scripts take js (finger width in units of 0.1 µm, 0.2 µm for SquidV0) and secondFinger (bent-finger width in µm, 0 = same): here they are finger_width and second_finger_width in µm.

The scripts set the finger parameters with change_pcell_parameters, so KLayout runs the legacy coerce_parameters_impl of JJ_finger Top/Bottom first (e.g. a 0.6 µm bent finger widens its 1 µm lead to 1.26 µm); coerce_straight() / coerce_bent() apply the same rules here.

Classes

SquidV0

Pre-HSQ SQUID (legacy junction_creator_sq.create_junction_squid; junction_pad.py with

TrilayerJunctionCompact

Compact single trilayer junction for dense junction test arrays (legacy chip_11m_TestJJ16x_pads.py

TrilayerJunctionHSQ

Single trilayer junction, first HSQ generation (legacy junction_creator_HSQ.create_junction).

TrilayerSquidHSQ

Two trilayer junctions forming a SQUID, first HSQ generation (legacy squid_creator_HSQ.create_squid).

Module Contents

class quantcore_circuits.layouts.junctions.legacy_junctions.SquidV0

Bases: quantcore_circuits.layouts.junctions.trilayer._TrilayerBase

Pre-HSQ SQUID (legacy junction_creator_sq.create_junction_squid; junction_pad.py with bent_window_height=16).

build()
bent_conn_height
bent_finger_length
bent_finger_y
bent_pad_width
bent_shift
bent_window_height
finger_width
junction_spacing
qcc_category = 'junction'
second_finger_width
straight_finger_length
straight_finger_y
straight_pad_width
window_height
with_hsq
class quantcore_circuits.layouts.junctions.legacy_junctions.TrilayerJunctionCompact

Bases: quantcore_circuits.layouts.junctions.trilayer._TrilayerBase

Compact single trilayer junction for dense junction test arrays (legacy chip_11m_TestJJ16x_pads.py create_testPad, cell JX_500, placed many times by chip_11f_JJplacer.py).

A 12 × 12 µm window (legacy junction_width + 1) holding a straight finger (1.2 µm lead) and a bent finger (1.6 µm lead), HSQ boxes 0.1 µm below / 0.2 µm above the finger, and a triangular notch (tip_width wide, from tip_depth to the window edge) cut from each finger window where its lead meets the edge. The legacy script fails with secondFinger=0 (undefined js); here second_finger_width=0 means “same as the straight finger”. The pads of the legacy script are commented out there; they are not drawn here either.

build()
bent_conn_height
bent_finger_length
bent_finger_x
bent_finger_y
bent_pad_width
bent_shift
finger_width
hsq_extra
hsq_extra_top
hsq_overlap
hsq_y
qcc_category = 'junction'
second_finger_width
straight_finger_length
straight_finger_y
straight_pad_height
straight_pad_width
tip_cut
tip_depth
tip_width
window_height
window_width
class quantcore_circuits.layouts.junctions.legacy_junctions.TrilayerJunctionHSQ

Bases: quantcore_circuits.layouts.junctions.trilayer.TrilayerJunction

Single trilayer junction, first HSQ generation (legacy junction_creator_HSQ.create_junction).

build()
bent_finger_y
bent_shift
hsq_extra
qcc_category = 'junction'
class quantcore_circuits.layouts.junctions.legacy_junctions.TrilayerSquidHSQ

Bases: quantcore_circuits.layouts.junctions.trilayer.TrilayerSquid

Two trilayer junctions forming a SQUID, first HSQ generation (legacy squid_creator_HSQ.create_squid).

build()
bent_conn_height
bent_finger_y
bent_shift
hsq_extra
qcc_category = 'junction'
straight_pad_height