DoublePadsSplines¶
A two-island qubit, consisting of two spline-constructed islands shunted by a junction,
Source: KQC (KQCircuits). Category: qubit. Module: kqcircuits.qubits.double_pads_splines.
Warning
Legacy cell. DoublePads with spline islands (same junction and model family); unused. Use DoublePads
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
350 |
90 |
10 |
6 |
coupler port (readout / bus); LOM node |
|
-450 |
0 |
180 |
10 |
6 |
drive / charge line end; control line (drive) in the LOM |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Mirror SQUID by its Y axis |
|
|
– |
Junction Type |
|
|
μm |
Junction width for code generated element |
|
|
– |
Width, height of the ground gap (µm, µm) |
|
|
μm |
Ground gap rounding radius |
|
|
– |
Width, height of the coupler (µm, µm) |
|
|
μm |
Coupler rounding radius |
|
|
μm |
Width of the coupler waveguide center conductor |
|
|
μm |
Distance from first qubit island to coupler |
|
|
μm |
Offset between SQUID center and qubit center |
|
|
– |
Width, height of the first qubit island (µm, µm) |
|
|
μm |
First qubit island rounding radius |
|
|
– |
Width, height of the second qubit island (µm, µm) |
|
|
μm |
Second qubit island rounding radius |
|
|
µm |
First qubit island tapering width on the island side |
|
|
µm |
First qubit island tapering width on the junction side |
|
|
µm |
Second qubit island tapering width on the island side |
|
|
µm |
Second qubit island tapering width on the junction side |
|
|
µm |
Island to island gap distance |
|
|
– |
Boolean whether to include the squid |
|
|
μm |
Length of fingers after the junction. |
|
|
– |
Include base metal gap layer |
|
|
– |
Junctions to separate layer |
|
|
μm |
Length of fingers inside the pads |
|
|
μm |
Width of the junction element. |
|
|
μm |
Height of the junction pad. |
|
|
μm |
Width of the junction pad. |
|
|
μm |
Pad separation. |
|
|
μm |
Rounding radius of the junction pad. |
|
|
– |
Disable the second junction |
|
|
– |
Control points of a B-Spline that defines left half of the island |
|
|
– |
Number of samples taken from each island spline |
|
|
μm^2 |
Loop area |
|
|
– |
Fluxline Type |
|
|
– |
Coordinate for the drive port (µm, µm) |
|
|
– |
Include base metal addition layer. |
|
|
μm |
Shadow layer margin near the the pads |
|
|
μm |
Junction lead offset from junction width |
|
|
– |
Move the junction lead offset to the other lead |
|
|
μm |
Height of the junction element. |
|
|
μm |
Horizontal junction offset. |
|
|
– |
Compact geometry for metal addition. |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island1 – gnd |
estimate=53.7, unit=fF, estimate_source=analytic: coupled strips in a ground slot (Simons ch. 7) + short-edge CPW, estimate_kind=analytic, uncertainty=±25% |
|
C |
island2 – gnd |
estimate=53.7, unit=fF, estimate_source=analytic: coupled strips in a ground slot (Simons ch. 7) + short-edge CPW, estimate_kind=analytic, uncertainty=±25% |
|
C |
island1 – island2 |
estimate=27.6, unit=fF, estimate_source=analytic: coupled strips in a ground slot (Simons ch. 7) + short-edge CPW, estimate_kind=analytic, uncertainty=±25% |
|
SQUID |
island1 – island2 |
Lj_nH=6.734, Cj_fF=15, asym=0, flux_phi0=0 |
|
C |
island1 – cplr |
estimate=13.8, unit=fF, estimate_source=analytic: coupler 150×20 µm facing island1 across 20 µm (CPS), estimate_kind=analytic, uncertainty=±25% |
|
C |
cplr – gnd |
estimate=7.6, unit=fF, estimate_source=rough: coupler pad in the qubit ground gap, estimate_kind=rough, uncertainty=±50% |
Nodes: island1, island2, cplr.
X: spline islands estimated as their bounding rectangles
X: floating transmon; island2 ↔ coupler capacitance neglected (screened by island1)
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "DoublePadsSplines", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.cplr") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components DoublePadsSplines lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.