Xmon¶
Grounded cross transmon with claw couplers; junction below the south arm.
Source: Quantcore. Category: qubit. Module: quantcore_circuits.layouts.qubits.xmon.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
254 |
90 |
10 |
6 |
readout claw (coupler; the readout CPW starts here); LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Notes from the catalog: claw tails (‘claw_n/w/e’) start the readout CPW: their clearance is claw_tail_gap (-1 = the element b, the chip CPW gap; claw_ground: claw_ground_gap) and the port declares exactly that (a = claw_tail_width); the claw body keeps the claw_spacing clearance. junction_type ‘Quantcore Junction’ / ‘Quantcore Squid’ = the PDK trilayer junctions; 3/0 keep-out = the legacy cross grown by 2*claw_base + 10 + claw_finger_width.
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Mirror SQUID by its Y axis |
|
|
– |
Junction Type |
|
|
μm |
Junction width for code generated element |
|
|
μm |
Cross arm width |
|
|
μm |
Cross tip-to-tip length |
|
|
μm |
Gap between cross and ground |
|
|
μm |
Ground between cross gap and claw clearance |
|
|
– |
Claws to draw (any of n, w, e) |
|
|
μm |
Claw clearance to ground |
|
|
μm |
Claw base thickness |
|
|
μm |
Claw finger width |
|
|
μm |
Claw finger length |
|
|
– |
Claw has a tail (connection stub) |
|
|
μm |
Claw tail length |
|
|
μm |
Claw tail width (CPW centre width at the port) |
|
|
– |
Ground frame around the claw |
|
|
μm |
Claw ground gap |
|
|
μm |
Claw tail gap to ground (= the readout CPW gap; -1 = the element’s b) |
|
|
– |
Add flux-line port and current slot below the junction |
|
|
– |
Junction cell parameters (JSON dict) |
|
|
– |
Metal window [width, height(, offset)] in the junction gap (legacy CLEARER; offset > 0 = away from the cross; empty = none) |
|
|
μm^2 |
Loop area |
|
|
– |
Fluxline Type (KQC) |
|
|
μm |
Flux tip x offset from the qubit axis |
|
|
μm |
Flux tip distance beyond the gap edge |
|
|
μm |
Flux slot size [length, width] (empty = none) |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island – gnd |
estimate=64.05, unit=fF, estimate_source=calibration Xmon.C_island (Q3D Q1R1 2026-11-02 (Si, rescaled (εr+1)/2)) |
|
JJ |
island – gnd |
Lj_nH=202.033, Cj_fF=0.5 |
|
C |
island – claw_n |
estimate=3.17, unit=fF, estimate_source=calibration Xmon.Cg (Q3D Q1R1 2026-11-02 (Si, rescaled (εr+1)/2)) |
|
C |
claw_n – gnd |
estimate=76.4, unit=fF, estimate_source=calibration Xmon.C_claw (Q3D Q1R1 2026-11-02 (Si, rescaled (εr+1)/2)) |
Nodes: island, claw_n.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "Xmon", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.claw_n") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components Xmon lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok.