TwoPadTransmon¶
Floating two-pad transmon (legacy Transmon); ports left / right at the lead ends.
Source: Quantcore. Category: qubit. Module: quantcore_circuits.layouts.qubits.legacy_transmon.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-35 |
0 |
180 |
10 |
6 |
pad coupling port; LOM node |
|
35 |
0 |
0 |
10 |
6 |
pad coupling port; LOM node |
|
-5 |
0 |
none |
10 |
6 |
junction pins (the LOM’s L_J); LOM node |
|
5 |
0 |
none |
10 |
6 |
junction pins (the LOM’s L_J); LOM node |
Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Pad thickness (along the axis) |
|
|
μm |
Pad height |
|
|
μm |
Gap between the pads (junction gap) |
|
|
μm |
Lead length outside each pad |
|
|
– |
Junction across the gap: none (legacy) or a trilayer cell |
|
|
– |
Trilayer junction cell parameters (JSON dict, e.g. lj_nH) |
|
|
μm |
Pocket beyond the pads in y (0 = no pocket, legacy) |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
island1 – gnd |
estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
|
C |
island2 – gnd |
estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
|
C |
island1 – island2 |
estimate=1.68, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
|
JJ |
island1 – island2 |
Lj_nH=–, Cj_fF=0 |
Nodes: island1, island2.
X: no junction drawn (junction_type ‘No Squid’); a JJ across the gap is assumed
X: no junction.Lj_nH in the design; the qubit mode needs one to simulate
X: two-pad transmon pads only (7.5 fF); the leads’ loads set C_Σ
Simulation export notes¶
C4: galvanic lead port shorted to ground / leaving the box (status: fixed; fix in sim_tools/builder.py (lead_open_ends, galvanic_routes, build_simulation))
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "TwoPadTransmon", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.left") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components TwoPadTransmon lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok. SQUID ports have no direction (null): ghost draws them as boxes (was the crash).