Gatemon

Carbon-nanotube gatemon island in an etched pocket with a gate feed (QPDK gatemon), M1 only.

Source: Quantcore. Category: qubit. Module: quantcore_circuits.layouts.qubits.qpdk_cells.

See also the catalog.

Pins

Pins of Gatemon

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

gate

60

-246

270

10

6

gate line end; LOM node gate

readout

0

75

90

150

40

readout coupling; LOM node island

squid_a

-40

-75

none

10

6

junction pins (the LOM’s L_J); LOM node island

squid_b

-40

-196

none

10

6

junction pins (the LOM’s L_J); grounded in the LOM

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: QPDK gatemon (MIT): M1 plus the CNT contacts, nanotube, hBN, Al patches and top gate on the proposed layers 600-604/0 (qpdk_cells.GATEMON_LAYERS; no fab numbers yet, draw_process_layers=False for M1 only). Port ‘readout’ is the island edge (a = island width, b = pocket_gap_top), not a CPW end: snap it to GatemonCoupler.qubit.

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

island_size

[150, 150]

[μm, μm]

Island (width, height)

pocket_gap

60

μm

Island to pocket side walls

pocket_gap_top

40

μm

Island to the readout side of the pocket

electrode_size

[60, 60]

[μm, μm]

Nb/Au landing pad (width, height)

electrode_spacing

100

μm

Gap between the landing pads

lead_width

2

μm

Contact stem width

junction_length

1

μm

Gap between the contact tips

junction_width

0.002

μm

Nanotube placement width

junction_offset

20

μm

Stems to weak link (x)

hbn_size

[80, 80]

[μm, μm]

hBN footprint (width, height)

size_patch

[60, 50]

[μm, μm]

Al reconnection patch (width, height)

gate_tip_width

16

μm

Top-gate tip width

gate_tip_gap

5

μm

hBN to M1 gate landing clearance

gate_length

50

μm

M1 gate CPW beyond the pocket

nanotube_contact_overlap

0.5

μm

Tube overlap onto each contact

electrode_offset

-40

μm

Contact stems x relative to the island

gate_offset

100

μm

Stems to the M1 gate feed (x)

draw_process_layers

true

–

Draw contacts, nanotube, hBN, patches and top gate (proposed fab 600–604/0)

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X

C

island – gnd

estimate=51.1, unit=fF, estimate_source=analytic: 150×150 µm island in its pocket (60 µm sides, 40 µm readout side), estimate_kind=analytic, uncertainty=±25%

J_X

JJ

island – gnd

Lj_nH=–, Cj_fF=0

Cgate_X

C

island – gate

estimate=0.2, unit=fF, estimate_source=rough: M1 gate tip beside the junction, below the island (rough, ±100 %), estimate_kind=rough, uncertainty=±50%

C_X_gate

C

gate – gnd

estimate=16, unit=fF, estimate_source=rough: gate feed CPW, estimate_kind=rough, uncertainty=±50%

Nodes: island, gate.

  • X: no junction.Lj_nH in the design; the qubit mode needs one to simulate

  • X: the CNT junction is not drawn; modelled as a JJ with the design’s junction values

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "Gatemon", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.gate")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components Gatemon lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.

GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok. ports without direction: squid_a, squid_b (ghost draws boxes).