quantcore_circuits.lom.kqc_models¶
LOM models for stock KQCircuits cells, registered from outside their classes (register_lom()).
This is the template for giving any third-party cell a lumped model: map its ports to nodes, add elements with
estimates (labelled calibration / analytic / rough, see estimates), and let FEM replace them
later by island name (<inst>.island, <inst>.island1/island2 for floating qubits, <inst>.<port> for
coupler pads).
KQC cell |
lumped model |
|---|---|
Swissmon |
grounded: island C (CPW-arm cross, anchored on the Xmon Q3D), JJ/SQUID to ground; per coupler node C_g + C to ground |
CircularTransmonSingleIsland |
grounded: disk C, JJ to ground; per arc coupler C_g + C to ground |
DoublePads, DoublePadsSplines |
floating: island1 (coupler side) and island2, each C to ground, C between them, JJ/SQUID between them; coupler node C_g to island1 |
ConcentricTransmon |
floating: island1 = outer ring, island2 = inner disk; arc couplers on the ring |
FingerCapacitorSquare/Taper, SmoothCapacitor, |
π network: C_ab between the ports, C to ground at each port |
CircularCapacitor, SpiralCapacitor |
|
QuarterWaveCpwResonator |
probe line |
HangerResonator |
probe line |
SpiralResonatorPolygon |
resonator line between a and b |
Launcher, LauncherDC |
50 Ω port |
WaveguideCoplanar, WaveguideComposite, |
a line: a wire between connected ports, a resonator when an end is |
Meander, WaveguideCoplanarCurved |
free (Meander: always a resonator, λ/2 bus between two couplers; Curved: r·|alpha|, ports from registry.KQC_EXTRA_PORTS) |
WaveguideCoplanarTaper, AirbridgeConnection |
a pass-through section ( |
WaveguideCoplanarSplitter |
one conductor (T-junction) |
FlipChipConnectorRf |
a pass-through section between |
AirbridgeRectangular, AirbridgeMultiFace |
wire; nothing joined: a ground strap (ports → gnd) |
junctions (Squid subclasses) |
JJ / SQUID from |
Fluxline* |
flux control port |
CapacitiveXCoupler |
arms p11..p41 (registry.KQC_EXTRA_PORTS), each C_ab (its finger
capacitor) to the floating centre |
Functions¶
|
KQC airbridge connection (CPW → bridge → CPW): a pass-through section (length: the builder takes the port |
|
KQC airbridges (rectangular, multi-face): a wire between their two pads; with no port joined, a ground strap |
|
KQC circular capacitor: centre disk (port a) and outer arc island (port b), C along the arc. |
|
KQC circular single-island transmon: grounded disk + JJ to ground, arc couplers between disk and ground. |
|
KQC concentric transmon: floating; island1 = outer ring (couplers face it), island2 = inner disk. |
|
KQC DoublePads: floating transmon, two rectangular islands shunted by a SQUID/JJ, one coupler ( |
|
KQC DoublePadsSplines: as DoublePads (spline islands approximated by their extents). |
|
KQC square finger capacitor: interdigital C_ab (Igreja–Dias) + tip gaps; C to ground across ground_padding. |
|
KQC tapered finger capacitor: interdigital C_ab; C to ground of each taper as a CPW section (gap b). |
|
KQC flip-chip RF connector (and Quantcore |
|
KQC flux line: its |
|
KQC hanger resonator: probe line |
|
A stand-alone junction cell (KQC/Quantcore |
|
KQC DC launcher: a pad to the outside world, modelled as a 50 Ω port (a DC bias source impedance). |
|
KQC wire-bond launcher: a 50 Ω port on the conductor its port connects to. |
|
KQC meander: a resonator line of |
|
KQC λ/4 CPW resonator element: probe line |
|
KQC smooth capacitor: the meandering gap between the electrodes as coplanar strips (rough). |
|
KQC spiral capacitor: two interleaved spiral fingers as coplanar strips along the spiral (rough). |
|
KQC polygon spiral resonator: one resonator line from port a to port b ( |
|
KQC CPW splitter (T / multiway junction): all ports are one conductor. |
|
KQC Swissmon: grounded cross transmon (island + JJ/SQUID to ground) with up to three coupler horseshoes. |
|
KQC composite waveguide: a line along its nodes (straight-segment length; inline elements are ignored). |
|
KQC CPW: a line along |
|
KQC curved CPW segment: a line of r·|alpha| between its ends |
|
KQC CPW taper: a pass-through section of |
|
KQC capacitive X coupler: four CPW arms (ports |
Module Contents¶
- quantcore_circuits.lom.kqc_models.airbridge_connection_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC airbridge connection (CPW → bridge → CPW): a pass-through section (length: the builder takes the port distance).
- quantcore_circuits.lom.kqc_models.airbridge_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC airbridges (rectangular, multi-face): a wire between their two pads; with no port joined, a ground strap (
Fragment.straps: both pads on the ground plane, ports → gnd).
- quantcore_circuits.lom.kqc_models.circular_capacitor_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC circular capacitor: centre disk (port a) and outer arc island (port b), C along the arc.
- quantcore_circuits.lom.kqc_models.circular_single_island_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC circular single-island transmon: grounded disk + JJ to ground, arc couplers between disk and ground.
- quantcore_circuits.lom.kqc_models.concentric_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC concentric transmon: floating; island1 = outer ring (couplers face it), island2 = inner disk.
- quantcore_circuits.lom.kqc_models.double_pads_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC DoublePads: floating transmon, two rectangular islands shunted by a SQUID/JJ, one coupler (
cplr).
- quantcore_circuits.lom.kqc_models.double_pads_splines_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC DoublePadsSplines: as DoublePads (spline islands approximated by their extents).
- quantcore_circuits.lom.kqc_models.finger_capacitor_square_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC square finger capacitor: interdigital C_ab (Igreja–Dias) + tip gaps; C to ground across ground_padding.
- quantcore_circuits.lom.kqc_models.finger_capacitor_taper_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC tapered finger capacitor: interdigital C_ab; C to ground of each taper as a CPW section (gap b).
- quantcore_circuits.lom.kqc_models.flip_chip_rf_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC flip-chip RF connector (and Quantcore
QcFlipChipConnectorRf): one conductor from porta(onface_ids[0]) through the bump to portb(onface_ids[1]), a pass-through section of the pad-to-pad length (each port is connector_a + s/2 from the centre; the bump itself is not modelled).
- quantcore_circuits.lom.kqc_models.fluxline_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC flux line: its
fluxport carries a flux-bias control (no circuit element).
- quantcore_circuits.lom.kqc_models.hanger_resonator_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC hanger resonator: probe line
pl(a, b) and a resonator line (resonator_a…resonator_b, unconnected KQC waveguide ends are grounded) coupled to it overcoupling_lengthacrossground_width.
- quantcore_circuits.lom.kqc_models.junction_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
A stand-alone junction cell (KQC/Quantcore
Squidsubclasses): JJ/SQUID fromcommonto ground.The junction’s lower electrode is the ground plane edge (its
origin_squid);Simjunctions expose the lumped-port endssquid_a(island side) andsquid_b(ground side).NoSquidhas no junction.
- quantcore_circuits.lom.kqc_models.launcher_dc_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC DC launcher: a pad to the outside world, modelled as a 50 Ω port (a DC bias source impedance).
- quantcore_circuits.lom.kqc_models.launcher_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC wire-bond launcher: a 50 Ω port on the conductor its port connects to.
- quantcore_circuits.lom.kqc_models.meander_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC meander: a resonator line of
length(λ/2 bus between two couplers, λ/4 with one grounded end).
- quantcore_circuits.lom.kqc_models.quarter_wave_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC λ/4 CPW resonator element: probe line
pl(ports a, b), a coupling capacitor (type_coupler) and the resonator line from the capacitor toresonator_b(galvanic termination = short).
- quantcore_circuits.lom.kqc_models.smooth_capacitor_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC smooth capacitor: the meandering gap between the electrodes as coplanar strips (rough).
- quantcore_circuits.lom.kqc_models.spiral_capacitor_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC spiral capacitor: two interleaved spiral fingers as coplanar strips along the spiral (rough).
- quantcore_circuits.lom.kqc_models.spiral_resonator_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC polygon spiral resonator: one resonator line from port a to port b (
term1/term2> 0 = open).
- quantcore_circuits.lom.kqc_models.splitter_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC CPW splitter (T / multiway junction): all ports are one conductor.
- quantcore_circuits.lom.kqc_models.swissmon_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC Swissmon: grounded cross transmon (island + JJ/SQUID to ground) with up to three coupler horseshoes.
Island: the four arms as CPW sections (arm width / gap width, WNES), scaled by the Xmon Q3D/analytic ratio at the Xmon calibration point. Couplers: C to ground = the horseshoe as a CPW of its width and
cpl_b(+ the port stub); C_g = the Xmon claw calibration at the coupler length (rough: the Swissmon coupler is screened by a ground strip, the Xmon claw is not). Run a C-matrix of the cell (q3d_cmatrix) to replace them.
- quantcore_circuits.lom.kqc_models.waveguide_composite_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC composite waveguide: a line along its nodes (straight-segment length; inline elements are ignored).
- quantcore_circuits.lom.kqc_models.waveguide_coplanar_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC CPW: a line along
path(a wire between two connected ports, a stub resonator if an end is free).
- quantcore_circuits.lom.kqc_models.waveguide_curved_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC curved CPW segment: a line of r·|alpha| between its ends
a(angle 0) andb(angle alpha; ports fromKQC_EXTRA_PORTS), as WaveguideCoplanar: a wire between connected ports, a stub with a free end (no termination: the end runs into ground).
- quantcore_circuits.lom.kqc_models.waveguide_taper_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC CPW taper: a pass-through section of
taper_lengthbetween a and b (inside a resonator it extends the line; the width step is not modelled: mean a/b).
- quantcore_circuits.lom.kqc_models.x_coupler_lom(name: str, inst, pdk) quantcore_circuits.lom.fragment.Fragment¶
KQC capacitive X coupler: four CPW arms (ports
p11..``p41``,KQC_EXTRA_PORTS) each coupled through its FingerCapacitorSquare (the element’s finger parameters, KQC’s default finger_length, ground_padding = b) to a floating centre cross (nodec): a star of four C_ab, as FingerCapacitorSquare’s estimate. C to ground: each arm’s CPW up to its capacitor, the centre’s four inner CPW sections, and half each capacitor’s finger block per side (rough).remove_capacitors: one conductor.