PadCoupler¶
Series gap capacitor of two facing pads (legacy Coupler); ports left / right.
Source: Quantcore. Category: coupler. Module: quantcore_circuits.layouts.others.couplers.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-35 |
0 |
180 |
10 |
6 |
pad coupling port; LOM node |
|
35 |
0 |
0 |
10 |
6 |
pad coupling port; LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Pad thickness (along the axis) |
|
|
μm |
Pad height |
|
|
μm |
Gap between the pads (junction gap) |
|
|
μm |
Lead length outside each pad |
|
|
– |
No junction on a coupler |
|
|
– |
Unused on a coupler |
|
|
μm |
Pocket beyond the pads in y (0 = no pocket, legacy) |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
left – right |
estimate=1.68, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
|
C |
left – gnd |
estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
|
C |
right – gnd |
estimate=5.85, unit=fF, estimate_source=analytic: two 20×30 µm pads across 10 µm in a 20 µm pocket (coupled strips + CPW), estimate_kind=analytic, uncertainty=±25% |
Nodes: left, right.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "PadCoupler", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.left") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components PadCoupler lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok.