TrilayerSquid¶
Two trilayer junctions forming a SQUID (legacy xjc_squid_TL_mod.create_squid).
Source: Quantcore. Category: junction. Module: quantcore_circuits.layouts.junctions.trilayer.
Note
Alias of QuantcoreSquid: the same circuit, drawn differently. finger_width 0.25, second_finger_width 0.6, clearer True = QuantcoreSquid (XOR 0)
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
0 |
20 |
none |
10 |
6 |
junction lead (the LOM’s L_J branch); LOM node |
Pins with direction none: common. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
– |
Junction Type |
|
|
μm |
Junction width for code generated element |
|
|
μm |
Straight finger width (junction size) |
|
|
μm |
Bent finger width (0 = same as straight) |
|
|
μm |
Exposure window width |
|
|
μm |
Straight finger length |
|
|
μm |
Straight finger offset (legacy y) |
|
|
μm |
Bent finger length |
|
|
μm |
Bent finger offset (legacy y) |
|
|
μm |
Bent finger lead width |
|
|
μm |
HSQ box width |
|
|
μm |
Distance of each junction from the axis |
|
|
μm |
Lead (pad) length of the straight fingers |
|
|
μm^2 |
Loop area |
|
|
μm |
Exposure window height (= qubit gap it spans) |
|
|
μm |
Bent finger cell shift in y |
|
|
– |
Draw HSQ sidewall boxes |
|
|
μm |
HSQ box extra length |
|
|
– |
Spacer gradient: 51–53/0 dose levels inside the 50/0 spacer (width / 3 strips; rings for windows) |
|
|
nH |
Size by the PDK junction rule for this L_J (SQUID: parallel total; 0 = use the finger widths) |
|
|
– |
Draw the CLEARER metal box under the windows (base_metal_addition) |
|
|
μm |
CLEARER inset from the window sides |
|
|
μm |
HSQ overlap onto the finger |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
SQUID |
j – gnd |
Lj_nH=101.016, Cj_fF=1, asym=0, flux_phi0=0 |
Nodes: j.
Simulation export notes¶
C3: junction sub-cell simulated on its own (status: fixed; fix in sim_tools/builder.py (is_junction_cell, _is_qubit, build_simulation); sim_tools/subset.py (has_junction))
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "TrilayerSquid", at=(3750, 3750), a=10) # parameters: see the table above
# no directed pin: place it with at= / rot=, or snap it with snap= / to=
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components TrilayerSquid lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect n/a (no directed port), build ok. ports without direction: common (ghost draws boxes).