metal:TransmonInterdigitated

The base “TransmonInterdigitated” inherits the “QComponent” class.

Source: Metal (Qiskit Metal). Category: qubit. Module: qiskit_metal.qlibrary.qubits.Transmon_Interdigitated.

See also the catalog.

Pins

Pins of metal:TransmonInterdigitated

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

bus1

-500

525

180

10

6

LOM node bus1

bus2

500

525

0

10

6

LOM node bus2

readout

0

-575

270

10

6

readout coupling; LOM node readout

squid_a

0

-25

none

10

6

junction pins (the LOM’s L_J); LOM node island1

squid_b

0

25

none

10

6

junction pins (the LOM’s L_J); LOM node island2

Pins with direction none: squid_a, squid_b. They mark a point (a junction lead, a pad centre), not a CPW end. The KLayout ghost draws them as boxes. A route can start there only where the notes say so; it cannot be snapped to.

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

junction_type

"Metal"

–

Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line

junction_params

"{}"

–

Trilayer junction cell parameters (JSON dict, e.g. lj_nH)

metal_class

"TransmonInterdigitated"

–

Quantum Metal component

options

"{}"

–

Metal options as JSON (bare numbers on length options are µm)

open_pins

""

–

Pins left open (comma-separated): keep Metal’s etch beyond them, as drawn with no route attached

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

branch

type

nodes

value (estimate at defaults)

C_X_12

C

island1 – island2

estimate=130, unit=fF, estimate_source=rough: 4 + 4 interdigital fingers (Igreja & Dias) + pad edges (CPS), estimate_kind=rough, uncertainty=±50%

C_X_1

C

island1 – gnd

estimate=160, unit=fF, estimate_source=rough: pad in its pocket, estimate_kind=rough, uncertainty=±50%

C_X_2

C

island2 – gnd

estimate=160, unit=fF, estimate_source=rough: pad in its pocket, estimate_kind=rough, uncertainty=±50%

J_X

JJ

island1 – island2

Lj_nH=–, Cj_fF=0

Cg_X_readout

C

island2 – readout

estimate=11, unit=fF, estimate_source=rough: CPS, estimate_kind=rough, uncertainty=±50%

Cc_X_readout

C

readout – gnd

estimate=23, unit=fF, estimate_source=rough: pad, estimate_kind=rough, uncertainty=±50%

Cg_X_bus1

C

island1 – bus1

estimate=11, unit=fF, estimate_source=rough: CPS, estimate_kind=rough, uncertainty=±50%

Cc_X_bus1

C

bus1 – gnd

estimate=23, unit=fF, estimate_source=rough: pad, estimate_kind=rough, uncertainty=±50%

Cg_X_bus2

C

island1 – bus2

estimate=11, unit=fF, estimate_source=rough: CPS, estimate_kind=rough, uncertainty=±50%

Cc_X_bus2

C

bus2 – gnd

estimate=23, unit=fF, estimate_source=rough: pad, estimate_kind=rough, uncertainty=±50%

Nodes: island1, island2, readout, bus1, bus2.

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "metal:TransmonInterdigitated", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.bus1")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components metal:TransmonInterdigitated lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.