PDK and fab¶
Questions about the Quantcore process rules and the mask the fab receives. The pages are PDK and fab export.
The PDK¶
What does the PDK fix?¶
One place for the Quantcore process: the stack (Nb on 650 µm sapphire, relative permittivity 10.25; a silicon variant
quantcore_nb_si_v1 is kept for comparison), the fab layers, the die frame, the pad rule, the keep-outs, the cheese,
corner rounding, the trilayer junction process and the kinetic inductance. get_pdk() returns it; every build uses it
unless the design names another. See PDK.
Which layers does the fab mask use?¶
The Quantcore negative-mask layers: 1 to 4, 50 to 53, 100, 300 / 301, 700, 800+, 500 / 501 (wafer level) and 1000+ (layer/datatype pairs such as 1/0 and 3/0). qcc mask --positive LAYER inverts one layer. The export writes only the PDK fab layers,
flat, and reports the layers it dropped. See fab export.
What is on the die frame?¶
A dicing L, alignment grids, an optional device ID and the brand QCT. The device ID is optional. Components and routes that touch a frame marker area or the ID raise a frame_keepout warning.
What is the 100 µm pad rule?¶
The outer edge of a pad’s etch sits 100 µm from the die edge. Place a pad with edge="auto" and it moves there. A pad
that is off the rule is a pad_edge design warning; in the plugin, Check > Fix pad edge warnings sets edge="auto" on
all flagged pads. When a design’s own pad position and the rule disagree, the PDK rule wins. See
PDK.
Why is a design warning not an error?¶
Margins against the PDK (pad_edge, pdk_rn, pdk_fq, pdk_claw) are flagged, never enforced, so a chip outside the
band still builds and exports. Read them as “check this on purpose”. See routing and DRC.
Keep-outs, cheese and rounding¶
What are the 3/0 keep-outs?¶
Layer 3/0 is the etch around the metal. Around a route it extends 10 µm, around a component 24 µm, and around any other shape 9 µm; a cell’s own keep-out grows by the same 4 µm step. 3/0 comes from the extended bounding box, and the 1/0 metal stays in the middle when the mask is exported: think of it as etching the features of 1/0 plus a margin.
What is the cheese?¶
Small square holes in the ground metal that pin magnetic flux vortices: 5 µm squares with 20 µm gaps, at least 4 µm
from the 3/0 keep-out, on both 1/0 and 3/0. By default they form a band three rows wide around the components. Set the
chip parameter cheese: "chip" to spread them over the whole die instead. If a design carries its own cheese, the
original cheese wins over the PDK band. See PDK.
Why does the whole-chip picture of a KQC example look like a solid sheet?¶
It shouldn’t any more. KQC grids its whole ground plane (with_grid: 5 µm holes on a 10 µm step), and at whole-chip
zoom that grid renders as solid colour. The KQC example chips now use cheese: "chip" instead: the PDK squares over
the whole die, which keeps KQC’s coverage at the PDK density. The layout shows the cheese the fab mask will get;
simulation exports never get cheese or rounding.
Are corners rounded?¶
Yes, by default in the fab export (--no-round switches it off). Simulation exports never round. Routes can also have
their own radius per corner. See fab export.
How do I export for fab?¶
Route |
How |
|---|---|
Python |
|
CLI |
|
Plugin |
Quantcore > Fab > Export for fab: a bundle with |
The plugin refuses while a route has failed. See fab export.
Can I still rebuild old designs after a PDK change?¶
That is the goal: the library and PDK must rebuild every existing design. When a rule changed (3/0 keep-outs, cheese on 3/0), all example fab exports were compared before and after. Wafer assembly (dies on a wafer) is described in Wafer assembly; a mask set is not built. See status.