SmoothCapacitorSemicircle¶
Coupling pad with a semicircular bite, placed on a qubit pin (SQDMetal Smooth_Capacitor_Semicircle).
Source: Quantcore. Category: capacitor. Module: quantcore_circuits.layouts.others.sqdmetal_cells.
See also the catalog.
Pins¶

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.
pin |
x (µm) |
y (µm) |
direction (°) |
a (µm) |
b (µm) |
purpose |
|---|---|---|---|---|---|---|
|
-60 |
0 |
180 |
10 |
6 |
CPW end; LOM node |
|
0 |
0 |
180 |
10 |
6 |
LOM node |
a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).
Notes from the catalog: SQDMetal Smooth_Capacitor_Semicircle (Apache-2.0). Port ‘target’ is a placement reference: snap it to the qubit pin (SQDMetal start_pin); routes start at ‘a’ (set lead_length to reach the pocket edge).
Parameters¶
name |
default |
unit |
description |
|---|---|---|---|
|
|
μm |
Width of center conductor |
|
|
μm |
Width of gap |
|
|
μm |
Turn radius |
|
|
μm |
Pad width (across) |
|
|
μm |
Pad length (towards the bite) |
|
|
μm |
Semicircle radius |
|
|
μm |
Clearance at the sides |
|
|
μm |
Clearance towards the bite |
|
|
μm |
Clearance behind the pad |
|
|
μm |
Width of the trace at port a |
|
|
μm |
Corner fillet radius (0 = sharp) |
|
|
μm |
CPW lead from the pad’s back edge to port a |
|
|
μm |
Semicircle centre beyond the pad front |
|
|
° |
Rotation of the drawing about the target pin |
|
|
– |
Fillet points per quarter circle |
Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.
LOM model¶
The cell contributes to the lumped model:
branch |
type |
nodes |
value (estimate at defaults) |
|---|---|---|---|
|
C |
pad – target |
estimate=27, unit=fF, estimate_source=rough: semicircle arc 192 µm around the qubit pad end, assumed 5 µm gap (CPS), estimate_kind=rough, uncertainty=±50% |
|
C |
pad – gnd |
estimate=59, unit=fF, estimate_source=rough: 190×170 µm pad in its clearance + lead, estimate_kind=rough, uncertainty=±50% |
Nodes: pad, target.
How to use¶
In Python:
from quantcore_circuits.designer import Designer
d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "SmoothCapacitorSemicircle", at=(3750, 3750), a=10) # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270) # a launcher to connect to
d.route("L1", "PAD.a", "U1.a") # a CPW from the pad to the pin
Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components SmoothCapacitorSemicircle lists the pins; add --schema for the parameters.
In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.
GUI status (kplugin/COMPONENTS_STATUS.md): places ok, edit ok, connect ok, build ok.