metal:ResonatorLumped

ResonatorLumped.png

Source: Metal (Qiskit Metal). Category: resonator. Module: qiskit_metal.qlibrary.resonators.resonator_lumped.

See also the catalog.

Pins

Pins of metal:ResonatorLumped

Pin image (default parameters). Light = metal, dark = etched gap, colours = junction layers. A red dot and arrow is a pin and its direction (out of the cell); the red bar is the CPW width a + 2 b. Blue dot = a pin without direction. Units: µm.

pin

x (µm)

y (µm)

direction (°)

a (µm)

b (µm)

purpose

pin_east

2500

0

0

10

6

grounded in the LOM

pin_n

0

3110

90

10

6

LOM node res

pin_ne

2500

2500

45

10

6

grounded in the LOM

pin_nw

-2500

2500

135

10

6

grounded in the LOM

pin_s

0

-2500

270

10

6

grounded in the LOM

pin_se

2500

-2500

315

10

6

grounded in the LOM

pin_sw

-2500

-2500

225

10

6

grounded in the LOM

pin_west

-2500

0

180

10

6

grounded in the LOM

a, b: CPW centre width and gap where the pin declares them (– = not declared). Position and direction are in the cell’s own frame (at=(0, 0), rot=0).

Notes from the catalog: draws metal only, no pocket (perimeter and trace are both metal): alone it is empty in the negative mask, as in Metal’s own GDS (metal on the ground plane). Place it on a pocket, e.g. metal:Rectangle with subtract: true; its metal goes to base_metal_addition, which the fab export removes from the etch. Metal’s defaults are mm-scale.

Parameters

name

default

unit

description

a

10

μm

Width of center conductor

b

6

μm

Width of gap

r

100

μm

Turn radius

junction_type

"Metal"

–

Junction as fabricated: Metal footprint, or a trilayer cell placed on each junction line

junction_params

"{}"

–

Trilayer junction cell parameters (JSON dict, e.g. lj_nH)

metal_class

"ResonatorLumped"

–

Quantum Metal component

options

"{}"

–

Metal options as JSON (bare numbers on length options are µm)

open_pins

""

–

Pins left open (comma-separated): keep Metal’s etch beyond them, as drawn with no route attached

Electrically relevant parameters (sizes, gaps, junction, ports) come first, the rest follows.

LOM model

The cell contributes to the lumped model:

  • no lumped branches

line

node

length (µm)

a (µm)

b (µm)

ends

X

res

69800

10

95

open / short

Nodes: res.

  • X: lumped resonator estimated as a λ/4 line of its trace length (rough)

Simulation export notes

  • ctx: scratch-context routing fallback (not an export issue) (status: context)

How to use

In Python:

from quantcore_circuits.designer import Designer

d = Designer("demo", box=(0, 0, 7500, 7500))
d.add("U1", "metal:ResonatorLumped", at=(3750, 3750), a=10)   # parameters: see the table above
d.add("PAD", "BondPad", at=(1125, 3750), rot=270)   # a launcher to connect to
d.route("L1", "PAD.a", "U1.pin_east")                # a CPW from the pad to the pin

Pin names go into d.route(...) as INSTANCE.pin, and into snap= / to= when placing. From the shell: qcc components metal:ResonatorLumped lists the pins; add --schema for the parameters.

In KLayout: Quantcore panel ▸ Components ▸ double-click the cell, then click on the layout to place it. Rotate and mirror before the click; use Connect on two pins to route.